Sets

Two silicone molds for:

• 4 Oval coasters. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and 8 mm (1/3") thick. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

Two silicone molds for:

• a set of 4 Heart shaped coasters. The coasters are 14.5 cm (5 7/10") wide. 13.5 cm (5 1/3") tall and 8 mm (1/3") thick.
• a mold that can be used to make a holder for the coasters and also a small Heart shaped tray. The heart is 18 cm (7") wide, 17 cm (6 3/4") tall and 8 mm (1/3") thick.
  The two small hearts are meant to be used as stands on the tray, to create a holder for the heart shaped coasters and they can for instance be fixed with glue, resin or in a toplayer.

There is also a mold available for a large heart shaped tray, see one of the pictures (for illustrative purposes, this item is only for the coaster mold with holder / small tray mold).

Three silicone molds for:

• a set of four Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick.
• a holder for the Hexagon coasters. The holder is large enough for hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. You can fix the six legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a medium sized Hexagon tray. The tray is 23 cm (9") wide, measured from corner to opposite corner, and 8 mm (1/3") thick.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

Set of 5 silicone inlay molds with the Crushed Ice pattern. The 'Island' mold is 15.5 x 21 cm (6" x 8 1/4") at the widest parts and the round inlay molds are 8 cm (3 1/6").

All molds are about 4 mm (1/6") thick and the round molds will fit in (almost) any coaster mold.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

Set of 2 molds for:

• 4 Halloween coasters, featuring a Spiderweb! The coasters are 12.5 cm (5") wide and 8 mm (1/3") thick. The Webdesign is 0.75 mm thick and it will be raised on the surface of the coasters.
• a large Halloween tray, also featuring a Spiderweb! The tray is 30 cm (12") wide and 8 mm (1/3") thick. The Big Web is also 0.75 mm thick and it will be raised on the surface of the tray.

Be a hit at any spooky party with this fun set of spiderweb coasters and tray. With big spiders for extra CREEPYNESS! They make for an eerie decorative combo that's sure to raise the hair on the backs of your guests' necks! Add these to your Halloween decor!

Both molds are also available separately.

Set of two silicone molds for our trays with the Magical theme. The trays are 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These two molds are part of our molds with the Magical theme, which further consists of a coaster mold, a coaster holder mold, a smaller tray, a larger tray and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Set of two silicone molds for our trays with the Oriental theme. The trays are 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These two molds are part of our molds with the Oriental theme, which further consists of a coaster mold, a coaster holder mold, a smaller tray, a larger tray and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

The figures in these molds present themself also in 12 cute Christmas ornaments, for which we have a mold available separately.

Set of 2 silicone molds for 4 Cascade Round coasters with a matching large tray. The coasters are 11 cm (4 1/3") wide and 9 mm (1/3") thick. The tray is 26.2 cm (10 1/3") wide and also 9 mm (1/3") thick. 

The coasters and tray are made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the coasters and tray a unique cascade-like appearance.

We also have other molds available with the layered Cascade design.

Two silicone molds for:

• a set of four oval coasters with a 'Wild Water' effect on the surface. The coasters are 12.5 x 9.5 cm (5" x 3 3/4") wide and 9 mm (1/3") thick.
• a large Oval tray with a 'Wild Water' effect on the surface. The tray is 28 x 19 cm (11" x 7 1/2") wide and 9 mm (1/3") thick.

Both molds are also available separately.

Add an artistic touch to your home with thesese 2 'Wild Water' molds. Create unique coasters and a large tray that are sure to make a splash with their wild water effect. Be bold and unleash your creativity with this ocean-inspired set.

Two silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

There are also molds available for two oval trays with the same graceful line pattern.

These two molds are together with the large oval tray 'Graceful lines' also as a set of 3 molds available, for a special setprice.

Set of two silicone molds for four irregular shaped Geode coasters and a matching holder. The Coasters are approx. 12.5 cm (5") wide and 15 mm (3/5") thick. The holder is 12 mm (1/2") thick.

Cure your thirst for something original with this set of 2 molds! The thick Geode coasters mold has an irregular shape and it comes with a holder mold, making it a unique set. Your guests won't be able to resist the 'rock'ing atmosphere! ;)

The molds are also available separately.

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

We also have a 28 cm (11") large tray mold available, with the same decorative engraving. 

Two silicone molds for a large and an XL round Trinket Dish. The large Trinket Dish has a diameter of 23 cm (9") and the XL Trinket Dish has a diameter of 28 cm (11").

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire disc 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Besides these two molds there are also Lily molds available for a set of 8 medallions and a tray of 25 cm (10"), as shown in one of the pictures (for illustrative purposes, this item is only for the coaster and holder mold).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

You can find Little Thumper not only on these two molds, he also appears on molds for a large tray, a set of 8 medallions, a tealight candle holder, a flower arranger and an egg holder tray. Everything you need to decorate a table for an Easter breakfast or Easter brunch!

Two silicone molds for a large 2-tier cake stand, engraved with the Peacock Mandala. The cake stands are 24 cm (9 2/5") and 30 cm (11 4/5") wide and 8 mm (1/3") thick. The centers have a hole of 6 mm (1/4") for the cakestand hardware, so no need to drill a hole.

The molds are part of our 'Peacock Mandala' design line, in which besides these molds are also a smaller cake stand (to make a 3-tier cake stand), a set of four coasters, a coaster holder and a mold for 8 medallions.