Ovaal

Silicone mold for an XL Oval tray. The tray is 24 x 35 cm (9 2/5" x 13 3/4") and 1 cm (2/5") thick.

We also have a large oval tray available, see one of the pictures (for illustrative purposes, this item is only for the extra large oval tray mold).

This oval tray is also available with a 'Graceful lines' engraving.

Silicone mold for a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

There are also molds available for matching coasters, a coaster holder and an XL tray, all engraved with the same graceful line pattern.

This mold is together with the matching coaster mold and coaster holder mold also as a set of 3 molds available, for a special setprice, see one of the pictures (for illustrative purposes, this item is only for the large oval tray mold).

This tray mold is also available in a plain version.

Silicone mold for a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") and 1 cm (2/5") thick.

We also have an XL oval tray available, see one of the pictures (for illustrative purposes, this item is only for the large oval tray mold).

This oval tray is also available with a 'Graceful lines' engraving.

Silicone mold for an XL Oval tray. The tray is 24 x 35 cm (9 2/5" x 13 3/4") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

There are also molds available for matching coasters, a coaster holder and a smaller tray, all engraved with the same graceful line pattern.

This tray is also available in a plain version.

Silicone mold for a set of 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.

There are also molds for a matching coaster holder and for two oval trays with the same graceful line pattern available, see one of the pictures (for illustrative purposes, this item is only for the oval coaster mold).

The molds are also in two sets available (coasters with holder, coasters with holder and large tray), for special setprices.

Silicone mold for a small Disc and Oval, both perforated with holes that are evenly spaced along the edges.

The disc is 10.5 cm (4") wide, 8 mm (1/3") thick and it has 28 holes. The center space between the holes is 8.3 cm (3 1/4") wide.

The oval is 10.5 x 15 cm (4" x 6") wide, 8 mm (1/3") thick and it has 34 holes. The center space between the holes is 8.3 x 12.8 cm (3 1/4" x 5") wide.

Silicone mold for a set of 4 Oval coasters. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.

There are also molds for a matching coaster holder and for two oval trays available, see one of the pictures (for illustrative purposes, this item is only for the oval coaster mold).

We have the molds also in two sets available (coasters with holder, coasters with holder and large tray), for special setprices.

There is also a mold available for the same size oval coasters, but then engraved with thin 'Graceful lines'.

Three silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.

Silicone mold for a large Oval tray. The tray has the shape of an egg and it is 25,5 cm (10") tall and 8 mm (1/3") thick.

 The tray is also part of our Easter collection, with molds for smaller decorations, large engraved oval trays and more (to come).

Silicone mold for a large Oval, perforated with 66 holes, evenly spaced along the edge of the oval. The oval is 28 x 19.5 cm (11" x 7 2/3") wide and 8 mm (1/3") thick.

Create a unique look with your own mix of lace, leather, ribbon, wicker and cotton. Get creative with braiding, crocheting or basket weaving - the sky's the limit to make your own one-of-a-kind creation with this mold!

Two silicone molds for:

• 4 Oval coasters. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and 8 mm (1/3") thick. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

Two silicone molds for:

• a set of four oval coasters with a 'Wild Water' effect on the surface. The coasters are 12.5 x 9.5 cm (5" x 3 3/4") wide and 9 mm (1/3") thick.
• a large Oval tray with a 'Wild Water' effect on the surface. The tray is 28 x 19 cm (11" x 7 1/2") wide and 9 mm (1/3") thick.

Both molds are also available separately.

Add an artistic touch to your home with thesese 2 'Wild Water' molds. Create unique coasters and a large tray that are sure to make a splash with their wild water effect. Be bold and unleash your creativity with this ocean-inspired set.

Two silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

There are also molds available for two oval trays with the same graceful line pattern.

These two molds are together with the large oval tray 'Graceful lines' also as a set of 3 molds available, for a special setprice.

Silicone mold for a large Oval tray with a 'Wild Water' effect on the surface. The tray is 28 x 19 cm (11" x 7 1/2") wide and 9 mm (1/3") thick.

Crafted with a creative and unique design resembling wild water, the oval tray that you create with this mold captures the wild energy of the sea in a powerful, artistic way. Bring out your inner artist, unleash your creative and artistic talents and create for instance a piece of Ocean art that resembles rough seas. An adventure for your imagination!

Two silicone molds for:

• 4 Oval coasters. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and 8 mm (1/3") thick. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide and 1 cm (2/5") thick.

Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.

There is also a mold available for an XL oval tray and all molds are also available engraved with thin 'Graceful lines'.

Silicone mold for a set of four oval coasters with a 'Wild Water' effect on the surface. The coasters are 12.5 x 9.5 cm (5" x 3 3/4") wide and 9 mm (1/3") thick. 

Unleash your creativity with our 'Wild Water' oval coasters! These unique coasters feature a rough texture that mimics the wild water effect, adding a bold touch to your drink serving experience.

Silicone mold for a holder for Oval coasters 'Graceful lines'. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and it can hold 4 of our oval coasters. The baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines.

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Silicone mold for a holder for Oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, 8 mm (1/3") thick and it can hold 4 of our oval coasters.

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

There are also molds for matching coasters and for two oval trays available, see one of the pictures (for illustrative purposes, this item is only for the oval holder mold).

We have the molds also in two sets available (coasters with holder, coasters with holder and large tray), for special setprices.

There is also a mold available for the same size oval coaster holder, but then engraved with thin 'Graceful lines'.