Alle mallen

Two silicone molds for a medium size and a large Trinket Dish. The medium Trinket Dish is 12.5 x 25 cm (5" x 10") wide and the large Trinket Dish is 15 x 30 cm (6" x 12") wide.

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire side 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Silicone mold for an XL Trinket Dish. The Trinket Dish is 17.5 x 35 cm (7" x 14") wide and it has two layers. The baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dish is in total 14 mm (just over 1/2") thick.

The raised edge is along the entire side 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

There are also molds for two smaller Trinket Dishes available, see one of the pictures (for illlustrative purposes, this item is only for the XL Trinket Dish). The three molds are also available in sets of two or three, for special setprices.

Silicone mold for a large holographic Christmas Bell + 6 small holographic Christmas Bells. The large Bell is 24.5 cm (9 2/3") wide and 25 cm (10") high. It also has a hole of 8 mm (1/3") at the top, to put a ribbon or cord through it. The Bell consists of two layers, a base layer of 8 mm (1/3") thick and on top of which a wireframe pattern of 0.75 mm thick is applied. The pattern will be raised on the surface of your beautiful creation.

The 6 small Christmas Bells vary in size from 5 cm (2") to about 8 cm (3"). They are 6 mm (1/4") thick and they have the pattern engraved in them. These bells also have holes for a hanging cord.

All bells have a holographic color effect, that will transfer to the surface of your resin Christmas bells.

We also have the same mold available without the holographic color effect.

Three silicone molds for:

• a set of 4 Scallop coasters. The coasters are 12.5 cm (5") x 11 cm (4 1/3") and 8 mm (1/3") thick.
• a mold that can serve as a holder mold for the Scallop coasters and also as a small tray mold. The scallop is 16.5 cm (6.5") x 14.5 cm (5 2/3") and 8 mm (1/3") thick .
  The two small scallops are meant to be used as stands on the tray, to create a holder for the scallop coasters and they can for instance be fixed with glue, resin or in a toplayer.
• a large Scallop tray. The tray is 25 cm (10") x 22.5 cm (9") and 8 mm (1/3") thick.

There are also Scallop molds available for an XL tray and for medallions, see some of the pictures (for illustrative purposes, this item is only for the coaster mold with holder and large tray mold).

Set of two silicone molds for 4 Holographic Hexagon coasters and a matching holder. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick. The matching holder can hold four Hexagon coasters of 8 mm thick. 

The silicone molds have holographic color effects, which  will transfer to the surface of your resin artwork. Both molds are also in a normal version available, without holographic effect.

The six legs of the holder have to be attached from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Silicone mold for a Tealight Candle Holder with a Druzy crystal heart. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a set of eight Holographic Fantasy (napkin ring) medallions. Each medallion is 5.5 cm (2 1/6") wide and 8 mm (about 1/3") thick. 

These medallions are the same as our normal Fantasy medallions, but then with a holographic color effect, which  will transfer to the surface of your resin medallions.

This medallion mold can be used together with our mold for the (napkin) rings, which is especially designed to form the base for these medallions. Together they make a unique napkin ring.

Silicone mold for a large shiny Tree of Life symbol. This mold has two layers, a round base of 26.5 cm (10 2/5") wide and 8 mm (1/3") thick and the tree of life which is 25 cm (10") wide and 7 mm (3/10") thick. This makes the total symbol 26.5 cm (10 2/5") wide and 15 mm (3/5") thick.

The iconic Tree of Life symbolizes growth, balance and harmony. Use your artistic talents to create a beautiful and unique symbol, embrace your inner tree hugger and add a touch of whimsy to every room.

We also have (a smaller) Tree of Life mold available which has a matte finish, perfect to use with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders.

Double, double toil and trouble, fire burn and cauldron bubble! (William Shakespeare)

Silicone mold for 4 coasters in the shape of a Whitch's Cauldron!! The cauldrons are 12.5 cm (5") wide, about 10 cm (4") high and 8 mm (1/3") thick.

There is also a mold available for a large Cauldron tray that can for instance be used for Halloween frontdoor or wall decoration. And both molds are also as a set available, see one of the pictures (for illustrative purposes, this item is only for the cauldron coaster mold).

Silicone mold for a Flower Arranger with a Holographic Broken Glass pattern. The Flower Arranger is 17 cm (6 2/3") wide and the holographic color effect will transfer to the surface of your resin flower arranger.

It's a known 'problem', you sometimes get a nice little bouquet of flowers, but you only have a vase that is too big to put them in. Then this Flower Arranger will be an outcome, because now you will be able to arrange the flowers nicely in that large vase.

This flower arranger mold has 5 holes and the same design is also available in a smooth version, without pattern (one of the pictures shows the smooth version 'in action').

There is also a 'Holo Broken Glass' version with 9 holes available.

Silicone mold for a holder for our Fantasy coasters.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is one of our molds with the Fantasy theme, which further consists of a coaster mold, 4 trays, 2 cakestands and a set of 8 medallions,.

Several of these molds are in sets available, for special setprices.

The holder mold is also in a holographic version available, for spectacular color effects on the surface of your resin coaster holder, especially when combined with the holographic Fantasy coasters.

Silicone mold for a large Holographic Magical tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.

The mold has a holographic color effect, which  will transfer to the surface of your resin artwork.

We also have holographic Magical molds available for coasters and a coaster holder, as seen in one of the pictures (for illustrative purposes, this item is only for the holographic Magical tray mold).

We also have Magical trays available in a normal version, without the holographic color effect.

Silicone mold for a set of 2 medium sized Decoration eggs. The eggs are 17,5 cm (7") tall and 6 mm (1/4") thick.

The mold can be used to make beautiful decorations for an Easter branch or tree.

We also have molds for smaller decoration eggs (including a holographic egg mold) and a tray in our collection.

Silicone mold for a large Holographic Decoration egg, that can for instance be used to decorate Easter branches or a tree. The egg is 20 cm (8") tall and 6 mm (1/4") thick. The holographic color effect will transfer to the surface of your resin egg.

We also have molds for smaller decoration eggs (including a holographic one) and a tray in our collection.

Set of 3 silicone molds for 4 Round Geode coasters with a matching holder and a large round Geode Tray. The coasters have the same shape as the tray and they are about 12.5 cm (appr. 5") wide and 8 mm (appr. 1/3") thick. The holder is specifically designed for these coasters. The Geode tray is 25 cm (10") wide and 10 mm (2/5") thick. 

You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The molds are also separately available.

Silicone mold for 28 Domino stones. These are special stones because the dots are hexagon shaped and the surface of the stones is uneven, which gives each stone a unique look! The stones are 24 mm x 50 mm (appr. 1" x 2") and about 6 mm (1/4") thick.

 A Domino tray mold is separately available, in which the 28 Domino stones can be stored, see one of the pictures (for illustrative purposes, this item is only for the mold for 28 domino stones).

Both molds are also as a set available, for a special setprice.

This mold is especially designed to use together with our mold for eight Hexagon medallions, see one of the pictures (for illustrative purposes, this item is only for the ring mold).

There are also hexagon shaped molds available for two trays, a set of four coasters and a matching coaster holder.