Alle mallen

Silicone mold for a holder for our Oriental coasters.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is one of our molds with the Oriental theme, which further consists of a coaster mold, 4 trays and a set of 8 medallions, see one of the pictures for some of them (for illustrative purposes, this item is only for the coaster holder mold).

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

The holder mold is also available in a Holographic version.

Silicone mold for a Holder for our 'Merry Christmas' coasters. The holder has the same decorative engraving as the 'Merry Christmas' coasters and tray.

The legs of the holder are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the 6 mm (1/4") thick base plate. You can fix the legs with a drop of glue or (UV) resin, so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The mold is also avalaible in a set with the coaster mold and in a set with both the coaster and tray mold, as shown in on of the pictures (for illustrative purposes, this item is only for the holder mold).

Silicone mold for a set of eight decorative (napkin ring) medallions, engraved with the Lily Mandala. Each medallion is 5.5 cm (2 1/6") wide and 8 mm (about 1/3") thick.

This medallion mold can be used together with our mold for the (napkin) rings, which is especially designed to form the base for these medallions. Together they make a unique napkin ring. 

This mold is part of our Lily Mandala line, which also includes a set of 4 coasters, a coaster holder ,a large tray of 25 cm (10") and an XL tray of 35.5 cm (14"), as shown in one of the pictures (for illustrative purposes, this item is only for the medallion mold).

Silicone mold for a set of four round Easter coasters, featuring Little Thumper with his brothers and sisters! The coasters are 10 cm (4") wide and 8 mm (1/3") thick.

There is also a matching coaster holder available, see one of the pictures (for illustrative purposes, this item is only for the coaster mold). Both molds are also as a set available, for a special setprice.

You can find Little Thumper not only on this mold and the holder mold, he also appears on molds for a large tray, a set of 8 medallions, a tealight candle holder, a flower arranger and an egg holder tray. Everything you need to decorate a table for an Easter breakfast or Easter brunch!

Silicone mold for a large oval tray, engraved with narcissuses. The oval tray has the shape of an egg, it's 28 cm (11") tall, 20 cm (8") wide and 8 mm (1/3") thick. 

Other engraved oval tray molds in our botanical collection are the daisies tray and the wild flowers tray, see one of the pictures (for illustrative purposes, this item is only for the mold with narcissuses).

Silicone inlay mold with a Honeycomb engraving. The size of the inlay mold is 19x 22 cm ( 7 1/2" x  8 2/3") and it is appr. 4 mm (1/6") thick.

The inlay is specifically matched to the size of our 23 cm (9") Medium Hexagon tray (item MOSH0192) and the thickness of this inlay mold makes it easy to create a tray with raised edge, by using that tray mold.

The same design inlay mold is also available for the 31 cm (12 1/8") large Hexagon tray and there is a holographic inlay mold for the medium sized Hexagon tray as well, as shown in one of the pictures (for illustrative purposes, this item is only for the Medium sized honeycomb inlay mold).

Silicone mold for a tray to store 28 Domino stones, to better prevent them from getting lost. This tray is meant to be used for the 28 Domino stones that are made with our Domino mold, which is also available in the shop. The dimensions of the tray are 21 cm x 25 cm (8 1/3" x 10") and it is in total 1 cm (2/5") thick. 

The tray has two layers, one for the decorative border, which is 6 mm (1/4") thick and a second layer of 4 mm (1/6") for the baseplate. The baseplate has a decorative pattern engraved into it.

The tray mold and the Domino stones mold are also as a set available, for a special setprice.

Silicone mold for a set of eight Holographic Oriental (napkin ring) medallions. Each medallion is 5.5 cm (2 1/6") wide and 8 mm (about 1/3") thick. 

These medallions are the same as our normal Oriental medallions, but then with a holographic color effect, which  will transfer to the surface of your resin medallions.

This medallion mold can be used together with our mold for the (napkin) rings, which is especially designed to form the base for these medallions. Together they make a unique napkin ring.

Silicone mold for an Art panel, titled Dunes I. The panel is 20 x 20 cm (8"x 8") wide and can maximum be 18 mm (7/10") thick. 

Transform your wall into a piece of art! This stunning mold features a subtle, flowing pattern reminiscent of serene sand dunes. The matte finish makes it perfect for working with Jesmonite and similar products that benefit from a natural, calm aesthetic.

Pair this mold with our Dunes II mold (available separately), to create a continuous pattern across your wall, as you can see in some of the pictures. Both molds are also available as a set, for a special setprice.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available for (wall) Art panels, these panels all have the same width of 20 x 20 cm and thickness may vary.

Silicone mold for a holder for Oval coasters 'Graceful lines'. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and it can hold 4 of our oval coasters. The baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines.

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Silicone mold for a holder for four Geode coasters which are 15 mm (3/5") thick. The holder itself is 12 mm (1/2") thick and only suitable for our matching 15 mm thick irregular shaped Geode coasters, see some of the pictures (for illustrative purposes, this item is only for the holder mold).

You can also pour two feet with this mold, they can be attached to the holder with glue or (UV) epoxy.

Both molds are also as a set available and the holder has the same shape as our rectangular Geode trays which are also available in the shop.

Silicone mold for a holder for our Ocean themed coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. 

You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Silicone mold for a Holder for our Cute Christmas coasters. The holder is engraved with a bunch of cute Christmas figures and it's suitable for every round coaster with a diameter of 10 cm (4"), but it's especially meant for our Cute Christmas coasters.

The legs of the holder are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the 6 mm (1/4") thick base plate. You can fix the legs with a drop of glue or (UV) resin, so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The figures in the holder present themself also in a set of 4 coasters, a large 30 cm (12") Christmas tray and in 12 cute Christmas ornaments, for which we have molds available separately.

Silicone mold for a holder for our Lily Mandala coasters. 

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This holder mold is part of our Lily Mandala line, which also includes a set of 4 coasters, a set of 8 medallions, a tray of 25 cm (10") and an XL tray of 35.5 cm (14"), as shown in one of the pictures (for illustrative purposes, this item is only for the holder mold).

The holder mold and coaster mold are also as a set available, for a special setprice.

Silicone mold for a holder for our Easter coasters, featuring Little Thumper with his brothers and sisters! The holder can hold 4 coasters of 10 cm (4") wide and 8 mm (1/3") thick.

You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This holder is a perfect match for the Easter coasters with the same engraved design, see one of the pictures (for illustrative purposes, this item is only for the holder mold).

Both molds are also as a set available, for a special setprice.

You can find Little Thumper not only on this mold and the coaster mold, he also appears on molds for a large tray, a set of 8 medallions, a tealight candle holder, a flower arranger and an egg holder tray. Everything you need to decorate a table for an Easter breakfast or Easter brunch!

 Silicone mold for a holder for our 'Mandala Peacock' coasters. 

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The holder mold is part of our 'Peacock Mandala' design line, in which besides this mold are also three cake stand molds (with center hole), a set of four coasters and a mold for 8 medallions.

The holder mold and coaster mold are also as a set available, for a special setprice.