Sets

Three silicone molds for:

• 4 Oval coasters. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and 8 mm (1/3") thick. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide and 1 cm (2/5") thick.

Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.

There is also a mold available for an XL oval tray and all molds are also available engraved with thin 'Graceful lines'.

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The figures in these molds present themself also in a large 30 cm (12") Christmas tray and in 12 cute Christmas ornaments, for which we have molds available separately.

Three silicone molds for:

• a set of four square coasters with an engraved Ocean theme. The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
  
• a holder for the Ocean coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a square Ocean tray. The tray is 25 x 25 cm (10" x 10") and 8 mm (1/3") thick.

Two silicone molds for:

• a set of four square coasters with an engraved Ocean theme. The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
  
• a holder for the Ocean coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Set of 2 silicone molds for Art panels, titled Dunes. Both panels are 20 x 20 cm (8"x 8") wide and they can maximum be 18 mm (7/10") thick. 

Make a statement! This set of Dunes I and Dunes II molds offers a seamless, serene flowing sand dunes pattern that can be spread across your entire wall. Ideal for those looking to create a large, impactful wall decoration. The matte finish makes them perfect for Jesmonite and similar products, allowing you to capture both the texture and natural beauty of sand dunes perfectly.

Both molds are also available separately.

!! ATTENTION: these molds don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in shiny (glossy) panels, they will have a matte finish.

We  also have other molds available for (wall) Art panels, these panels all have the same width of 20 x 20 cm and thickness may vary.

Three silicone molds for:

• a set of four Slate coasters. The coasters are appr. 11 x 13 cm (4 1/3"x 5 1/10") and 6 mm (1/4") thick.
• a holder for the Slate coasters. 
• a large oval Slate tray. The tray is 30 cm x 22.5 cm (12" x 8 4/5") large and 8 mm (1/3") thick.

The edges of the coasters, holder and tray are coarsened, for that specific slate look and feel.

The molds have a smooth surface, the 'crushed ice' effect that is shown in one of the pictures, is made with some of our inlay molds, which are available separately.