Sets

Two silicone molds for:

• 4 square coasters with a rough tumbled marble look and feel. The coasters are 10 x 10 cm (4" x 4") wide and 1 cm (2/5") thick.
• a square tray with a rough tumbled marble look and feel. The tray is 20 x 20 cm (8" x 8") wide and 1 cm (2/5") thick.

!! ATTENTION: these molds don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) set of coasters and tray, they will have a matte finish.

The molds are also available separately.

Set of 2 silicone molds for 4 Cascade Hexagon coasters with a matching large tray. The coasters are from side to side 11 cm (4 1/3") wide and 9 mm (1/3") thick. The tray is from side to side 25 cm (10") wide and also 9 mm (1/3") thick. 

The coasters and tray are made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the coasters and tray a unique cascade-like appearance.

We also have other molds available with the layered Cascade design.

Two silicone molds for:

• a set of 4 Scallop coasters. The coasters are 12.5 cm (5") x 11 cm (4 1/3") and 8 mm (1/3") thick.
• a mold that can be used to make a holder for the Scallop coasters and also a small Scallop tray. The scallop is 16.5 cm (6.5") x 14.5 cm (5 2/3") and 8 mm (1/3") thick .
  The two small scallops are meant to be used as stands on the tray, to create a holder for the scallop coasters and they can for instance be fixed with glue, resin or in a toplayer.

There are also Scallop molds available for 2 larger trays and for medallions, see one of the pictures (for illustrative purposes, this item is only for the coaster mold with holder / small tray mold).

Two silicone molds for:

• a set of four round coasters with a 'Wild Water' effect on the surface. The coasters are 11.5 cm (4 1/2") wide and 9 mm (1/3") thick. 
• a large round tray with a 'Wild Water' effect on the surface. The tray is 30 cm (11 4/5") wide and 9 mm (1/3") thick.

Both molds are also available separately.

Add an artistic touch to your home with thesese 2 'Wild Water' molds. Create unique coasters and a large tray that are sure to make a splash with their wild water effect. Be bold and unleash your creativity with this ocean-inspired set.

Three silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.

Set of three silicone molds for our trays with the Magical theme. The trays are 15 cm (6"), 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These three molds are part of our molds with the Magical theme, which further consists of a coaster mold, a coaster holder mold, an XL tray and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Three silicone molds for:

• a set of 4 Heart shaped coasters. The coasters are 14.5 cm (5 7/10") wide. 13.5 cm (5 1/3") tall and 8 mm (1/3") thick.
• a mold that can be used to make a holder for the coasters and also a small Heart shaped tray. The heart is 18 cm (7") wide, 17 cm (6 3/4") tall and 8 mm (1/3") thick.
  The two small hearts are meant to be used as stands on the tray, to create a holder for the heart shaped coasters and they can for instance be fixed with glue, resin or in a toplayer.
• a large Heart shaped tray. The tray is 30 cm (12") wide, 27.8 cm (11")  tall and 8 mm (1/3") thick.

All molds are also available separately.

Three silicone molds for:

• a set of four Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick.
• a holder for the Hexagon coasters. The holder is large enough for hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. You can fix the six legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Hexagon tray. The tray is 31 cm (12 1/8") wide, measured from corner to opposite corner, and 8 mm (1/3") thick.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

Three silicone molds for Decorative Christmas ornaments, one with a Christmas tree, one with a Snowflake and one with a Curls design. Each ornament is 15 cm (6") tall, 11 cm (4 1/3") wide and 6 mm (1/4") thick. The decorative pattern on the ornaments are 0.75 mm thick and they will be raised on the surface of the ornaments.

The molds are also available separately.

Set of 2 silicone molds for 4 Cascade Roman coasters with a matching large tray. The coasters are 11 cm (4 1/3") wide and 9 mm (1/3") thick. The tray is 25 cm (10") wide and also 9 mm (1/3") thick. 

The coasters and tray are made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the coasters and tray a unique cascade-like appearance.

We also have other molds available with the layered Cascade design.

Two silicone molds for:

• a set of four square coasters with a raised edge and a 'Tetris' pattern. The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.

• a matching holder, which holds 4 coasters of maximum 8 mm (1/3") thick. You can fix the supports with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

  Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The coaster mold and the holder mold are also separately available.

Two silicone molds for a medium sized 2-tier cake stand, engraved with the Peacock Mandala. The cake stands are 18 cm (7") and 24 cm (9 2/5") wide and 8 mm (1/3") thick. The centers have a hole of 6 mm (1/4") for the cakestand hardware, so no need to drill a hole.

The molds are part of our 'Peacock Mandala' design line, in which besides these molds are also a larger cake stand (to make a 3-tier cake stand), a set of four coasters, a coaster holder and a mold for 8 medallions.

Set of 2 silicone molds for:

• four Cobble Coasters. The coasters are 13 cm (5 1/9") wide, 10.5 cm (4 1/7") high and 8 mm thick.
• a large Cobble Tray. The tray is 25 cm (10") wide, 25 cm (10") high and 8 mm thick.

This matching mold set combines the Large Cobble Tray with four coordinated Cobble Coasters. Their softly irregular shapes create a beautifully balanced collection with a modern, organic feel. Use matching colours and effects for a harmonious table set, or give each piece its own individual character. Perfect for stylish home décor, entertaining or creating an impressive handmade gift set.

3 Silicone molds for Halloween Bat Hangers: 

• a small Bat Hanger, which is 20 cm (8") wide and 8 cm (3 1/4") high.
• a medium size Bat Hanger, which is 25 cm (10") wide and10 cm (4") high.
• a large Bat Hanger, which is 35 cm (12") wide and 12.5 cm (5") high.

The bats are 8 mm (1/3") thick and they have a raised decorative pattern, which is 1 mm thick.

The three molds are also available separately.

Three silicone molds for Christmas Baubles with a decorative ribbon:

• Two baubles of 10 cm (4") wide and 13.5 cm (5 1/3") high.
• One bauble of 15 cm (6") wide and 20.5 cm (8") high.
• One bauble of 20 cm (8") wide and 27.5 (10 4/5") high.

Each bauble is 8 mm (1/3") thick and the molds are also available separately.

Set of three silicone molds for our trays with the Oriental theme. The trays are 15 cm (6"), 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These three molds are part of our molds with the Oriental theme, which further consists of a coaster mold, a coaster holder mold, an XL tray and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Set of two silicone molds for our trays with the Oriental theme. The trays are 15 cm (6") and 20 cm (8") wide and 8 mm (1/3") thick.

These two molds are part of our molds with the Oriental theme, which further consists of a coaster mold, a coaster holder, 2 larger trays and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Two silicone molds for:

• 4 Oval coasters. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and 8 mm (1/3") thick. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.