Holografisch

Silicone mold for 6 Holographic Christmas Bell ornaments, with holes for a ribbon or cord. Each bell is 10 cm (4") wide and high, 6 mm (1/4") thick and they have a holographic color effect, that will transfer to the surface of your resin Christmas ornaments.

We also have a mold available for the same ornaments, but then without the holographic color effect.

Silicone mold for a Tealight Candle Holder with a Holographic Fireplace. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The cosy and colorful fire is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration, see the pictures. A few of them are pictured in their finished state.

Silicone mold for a Flower Arranger with a Holographic Broken Glass pattern. The Flower Arranger is 17 cm (6 2/3") wide and the holographic color effect will transfer to the surface of your resin flower arranger.

It's a known 'problem', you sometimes get a nice little bouquet of flowers, but you only have a vase that is too big to put them in. Then this Flower Arranger will be an outcome, because now you will be able to arrange the flowers nicely in that large vase.

This flower arranger mold has 9 holes and the same design is also available in a smooth version, without pattern (one of the pictures shows the smooth version 'in action').

There is also a 'Holo Broken Glass' version with 5 holes available.

Silicone mold for two Holographic Intertwined Hearts. The hearts are 8 mm (1/3) thick and together they are 26.5 cm (10 2/5") wide and 19.5 cm (7 2/3") tall.

The mold has a holographic color effect, which  will transfer to the surface of your resin hearts.

The mold is also available in a regular verison, without the holographic color effect.

Silicone mold for a small Holographic Geode tray. The tray is 18 cm (7") wide and 8 mm (1/3") thick.

The mold has a holographic color effect, which  will transfer to the surface of your resin artwork.

We have the same holographic tray also in a larger 28 cm (11") version available.

Set of 4 silicone Holographic inlay molds, in the shape of a heart. Each heart is 13.3 cm (5 1/4") wide, 11.8 cm (4 2/3") tall and appr. 5 mm (1/5") thick.

These inlay molds are especially designed for our heart shaped coaster mold, which is available separately. Because the inlay molds are appr. 5 mm thick, the result will be a heart shaped coaster with a raised edge.

The molds have a holographic color effect, which  will transfer to the surface of your resin hearts. Please be aware that when you pour a finishing (top) layer over the holographic piece, the holographic effect will be gone! We therefore advise not to use a top coat.

Silicone mold for a Holographic holder for 4 (holographic) Fantasy coasters. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Fantasy coasters, see one of the pictures (for illustrative purposes, this item is only for the holographic holder mold). Both holographic molds are also as a set of 2 molds available, for a special setprice.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Silicone mold for a Holographic Tealight Candle Holder with the AUM (OHM/OM) symbol. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The symbol is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration, see the pictures. A few of them are pictured in their finished state.

Silicone mold for a large Holographic Oriental tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.

The mold has a holographic color effect, which  will transfer to the surface of your resin artwork.

We also have holographic Oriental molds available for coasters and a coaster holder, as seen in one of the pictures (for illustrative purposes, this item is only for the holographic Oriental tray mold).

We also have Oriental trays available in a normal version, without the holographic color effect.

Silicone mold for 4 medium size Holographic Christmas Angels. Each Angel is 15 cm (6") tall, 6 mm (1/4") thick and they have a holographic color effect, that will transfer to the surface of your resin Christmas angels.

We also have a mold available for 6 Holographic Christmas Angels of 10 cm (4") each, see one of the pictures (for illustrative purposes, this item is only for the mold with 4 Christmas Angels).

Both molds are also available in a version without the holographic color effect and  in a version with druzy crystal Angel wings.

Silicone square inlay mold with a Holographic decorative lead glass 'Daisy bud' pattern. The mold is 18 x 18 cm (7" x 7") wide and 5 mm (1/5") thick. The 'Daisy bud' pattern is 0.75 mm deep.

This inlay mold will make a great combination together with our 20 x 20 cm (8" x 8") large tray molds of 1 cm (2/5") and 2 cm (4/5") thickness. Using the two molds together will create a tray with a raised edge of 5 mm (1/5").

There is also a larger normal version of this inaly mold available, without the holographic color effect. And we also have 8 mm (1/3") tray molds with this 'Daisy bud' pattern available, in a normal and in a holographic version.

Silicone mold for a Holographic holder for 4 round Geode coasters, that are maximum 12.5 cm (5") wide and 8 mm (1/3") thick. The holder is the same as the holder for our normal round Geode coasters, but then with a holographic color effect, which  will transfer to the surface of your resin coaster holder.

This holder is specifically designed for our Holographic Geode Coasters, see one of the pictures (for illustratives purposes, this item is only for the holder mold). Both the holographic holder and matching coaster mold are as a set available, for a special setprice.

You insert the legs from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Silicone mold for a Holographic holder for 4 (holographic) Hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Hexagon coasters, see one of the pictures (for illustrative purposes, this item is only for the holder mold).

Both holographic molds are also as a set of 2 molds available, for a special setprice.

The six legs of the holder have to be attached from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Silicone mold for a set of 4 Holographic Oriental coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.

These coasters have the same shape as our other Oriental coasters, but then with a holographic color effect, which  will transfer to the surface of your resin coasters.

There are also molds available for a holographic Oriental coaster holder and a large holographic Oriental tray, see one of the pictures (for illustrative purposes, this item is only for the holographic coasters mold). We also combined the 3 molds in 2 different available sets, for special setprices.

This mold is also available in a normal version, wihout the holographic color effect.

Silicone mold for a set of eight Holographic Magical (napkin ring) medallions. Each medallion is 5.5 cm (2 1/6") wide and 8 mm (about 1/3") thick. 

These medallions are the same as our normal Magical medallions, but then with a holographic color effect, which  will transfer to the surface of your resin medallions.

This medallion mold can be used together with our mold for the (napkin) rings, which is especially designed to form the base for these medallions. Together they make a unique napkin ring.

Silicone mold for a square Holographic tray with a decorative lead glass 'Daisy bud' pattern. The surface of the tray has a holographic finish, which will result in beautiful shifting color effects on your resin tray.

The tray is 24.5 cm x 24.5 cm (9 3/5" x 9 3/5") wide and in total almost 9 mm (1/3") thick. The 'Daisy bud' pattern is 0.75 mm thick and it will be raised on the surface of the tray.

There is also a normal version of the same tray design available, without the holographic color effects. And both versions of this 'Daisy bud' pattern are also available as 5 mm (1/5") thick inlay molds, for our 1 cm and 2 cm deep square tray molds.

Silicone mold for a Holographic holder for 4 (holographic) Magical coasters. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Magical coasters, see one of the pictures (for illustrative purposes, this item is only for the holder mold). Both holographic molds are also as a set of 2 molds available, for a special setprice.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is also available in a normal version, without the holographic color effect.

Silicone mold for a Holographic holder for 4 (holographic) Oriental coasters. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Oriental coasters, see one of the pictures (for illustrative purposes, this item is only for the holder mold). Both holographic molds are also as a set of 2 molds available, at a special setprice.

The legs of the holder are 44 mm (1 3/4") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is also available in a normal version, without the holographic color effect.

Silicone mold for a set of eight Holographic Oriental (napkin ring) medallions. Each medallion is 5.5 cm (2 1/6") wide and 8 mm (about 1/3") thick. 

These medallions are the same as our normal Oriental medallions, but then with a holographic color effect, which  will transfer to the surface of your resin medallions.

This medallion mold can be used together with our mold for the (napkin) rings, which is especially designed to form the base for these medallions. Together they make a unique napkin ring.