Producten

Set van twee siliconen mallen voor vier Leisteen onderzetters met bijpassende houder. De onderzetters zijn ongeveer 11 x 13 cm en ze zijn 6 mm dik. De randen van de onderzetters en de houder zijn verruwd, zodat ze de specifieke uitstraling van leisteen hebben.

Er is ook een een mal voor een bijpassende ovale tray verkrijgbaar, zoals op één van de foto's getoond (ter illustratie, de tray mal is niet in dit item inbegrepen).

De mallen zijn ook los verkrijgbaar en er is ook een set van vier ovale Druzy inlegmallen voor de leisteen onderzetters.

Two silicone molds for:

• a set of two Tube coasters. The coasters are 12.5 x 12.5 cm (5" x 5") wide and 1 cm thick.
• a Tube tray. The tray is 12.5 x 25 cm (5" x 10") wide and 1 cm (2/5") thick.

Both the coasters and the tray have a flat bottom and the top consists of 5 adjacent tubes. 

!! ATTENTION: these mold don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in shiny (glossy) coasters and tray, they will have a matte finish, as shown in the pictures.

The molds are also available separately.

Two silicone molds for:

• 4 square coasters with a rough tumbled marble look and feel. The coasters are 10 x 10 cm (4" x 4") wide and 1 cm (2/5") thick.
• a square tray with a rough tumbled marble look and feel. The tray is 20 x 20 cm (8" x 8") wide and 1 cm (2/5") thick.

!! ATTENTION: these molds don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) set of coasters and tray, they will have a matte finish.

The molds are also available separately.

Double, double toil and trouble, fire burn and cauldron bubble! (William Shakespeare)

Two silicone molds for:

• 4 coasters in the shape of a Whitch's Cauldron!! The coasters are 12.5 cm (5") wide, about 10 cm (4") high and 8 mm (1/3") thick.
• a large Whitch's Cauldron tray. The tray is 30 cm (12") wide, about 24 cm (9 1/3") high and 8 mm (1/3") thick.

The coasters and tray will be beautiful as Halloween decoration. The molds are also available separately.

Two silicone molds for:

• a set of four square coasters with an engraved Ocean theme. The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
  
• a holder for the Ocean coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Two silicone molds for:

• a set of four square coasters with a raised edge and a 'Tetris' pattern. The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.

• a matching holder, which holds 4 coasters of maximum 8 mm (1/3") thick. You can fix the supports with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

  Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The coaster mold and the holder mold are also separately available.

Three silicone molds for:

• a set of four Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick.
• a holder for the Hexagon coasters. The holder is large enough for hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. You can fix the six legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Hexagon tray. The tray is 31 cm (12 1/8") wide, measured from corner to opposite corner, and 8 mm (1/3") thick.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

Three silicone molds for:

• a set of four Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick.
• a holder for the Hexagon coasters. The holder is large enough for hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. You can fix the six legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a medium sized Hexagon tray. The tray is 23 cm (9") wide, measured from corner to opposite corner, and 8 mm (1/3") thick.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

Three silicone molds for:

• a set of four square Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
• a holder for the Kintsugi coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a square Kintsugi tray. The tray is 25 x 25 cm (10" x 10") and 8 mm (1/3") thick.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

The molds are also available separately.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

The figures in these molds present themself also in 12 cute Christmas ornaments, for which we have a mold available separately.

Three silicone molds for Decorative Christmas ornaments, one with a Christmas tree, one with a Snowflake and one with a Curls design. Each ornament is 15 cm (6") tall, 11 cm (4 1/3") wide and 6 mm (1/4") thick. The decorative pattern on the ornaments are 0.75 mm thick and they will be raised on the surface of the ornaments.

The molds are also available separately.

Three silicone molds for Druzy Crystal Christmas ornaments, one with a Christmas tree, one with a Christmas star and one with a Cristmas bell. Each ornament is 15 cm (6") tall, 11 cm (4 1/3") wide and 6 mm (1/4") thick.

The molds are also available separately.

Set of three silicone molds for our trays with the Fantasy theme. The trays are 15 cm (6"), 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These three molds are part of our molds with the Fantasy theme, which further consists of a coaster mold, a coaster holder, 1 larger tray, 2 cakestands and a set of 8 medallions.

We made several of these molds in sets available, for special setprices.

Three silicone molds for:

• a set of 4 Heart shaped coasters. The coasters are 14.5 cm (5 7/10") wide. 13.5 cm (5 1/3") tall and 8 mm (1/3") thick.
• a mold that can be used to make a holder for the coasters and also a small Heart shaped tray. The heart is 18 cm (7") wide, 17 cm (6 3/4") tall and 8 mm (1/3") thick.
  The two small hearts are meant to be used as stands on the tray, to create a holder for the heart shaped coasters and they can for instance be fixed with glue, resin or in a toplayer.
• a large Heart shaped tray. The tray is 30 cm (12") wide, 27.8 cm (11")  tall and 8 mm (1/3") thick.

All molds are also available separately.