Alle mallen

Silicone mold for a small 'Fantasy' tray. The tray is 15 cm (6") wide and 8 mm (1/3") thick.

This mold is one of our molds with the Fantasy theme, which further consists of a coaster mold, a coaster holder, 3 larger trays, 2 cakestands and a set of 8 medallions.

We made several of these molds in sets available, for special setprices.

Silicone mold for a large Cascade Pebble tray. The tray is 20.5 cm (8") wide, 25 cm (10") high and 9 mm (1/3") thick. 

The tray is made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the tray a unique cascade-like appearance.

We have this tray also in an XL version available.

There is also a Pebble coaster mold available with the same cascade design, see one of the pictures (for illustrative purposes, this items is only for the Pebble tray mold). Both molds are also available as a set, at a special price.

Set of 2 silicone molds for 4 Cascade Daisy coasters with a matching large tray. The coasters are 12 cm (4 3/4") wide and 9 mm (1/3") thick. The tray is 26 cm (10 1/4") wide and also 9 mm (1/3") thick. 

The coasters and tray are made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the coasters and tray a unique cascade-like appearance.

We also have other molds available with the layered Cascade design.

Silicone mold for a set of four Cascade Daisy coasters. The coasters are 12 cm (4 3/4") wide and 9 mm (1/3") thick. 

The coasters are made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the coasters a unique cascade-like appearance.

There is also a Daisy tray mold available with the same cascade design, see one of the pictures (for illustrative purposes, this items is only for the coasters mold). Both molds are also available as a set, at a special price.

Siliocone mold for a round disc with ribbed edge. The disc is 15 cm (6") wide and  8 mm (1/3") thick.

There are also molds available for two larger ribbed edge trays of 25 cm (10") and 35.5 cm (14) and for ribbed edge coasters and matching coaster holder, see one of the pictures (for illustrative purposes, this item is only for the 15 cm disc mold).

Silicone mold for a Flower Arranger with a diameter of 17 cm (6 2/3").

It's a known 'problem', you sometimes get a nice little bouquet of flowers, but you only have a vase that is too big to put them in. Then this Flower Arranger will be an outcome, because now you will be able to arrange the flowers nicely in that large vase.

This mold has 5 holes and there is also a mold available with 9 holess, see one of the pictures (for illustrative purposes, this item is only for the mold with 5 holes).

There is also a Holographic version of this mold available and also a mold for a much larger Flower Arranger of 27.5 cm (11") with 21 holes.

Thanks to Atelier 'De Schone Schijn' for the pictures with the white Flower Arranger.

Silicone mold for a set of eight decorative (napkin ring) 'Fantasy' medallions. Each medallion is 55 mm (2 1/6") wide and 8 mm (about 1/3") thick.

This medallion mold can be used together with our mold for the (napkin) rings, which is especially designed to form the base for these medallions. Together they make a unique napkin ring.

The medallion mold is part of our molds with the Fantasy theme, which further consists of a coaster mold, a coaster holder, 2 cake stands and 4 trays, see one of the pictures (for illustrative purposes, this item is only for the medallion mold).

We made several of these molds in sets available, for special setprices.

Silicone mold for a Christmas Trinket Dish, shaped as a friendly Gnome. The trinket dish is 25 cm (10") high, 13.5 cm (5 1/4") wide and 18 mm (7/10") thick, including a raised edge of 8 mm (1/3").

Add a touch of festive cheer to your home with a playful Gnome Trinket Dish. Perfect for holding small treasures or holiday treats, it brings a whimsical spirit to your Christmas decorations.

!! ATTENTION: only the Gnome itself has a smooth glossy finish (hat, beard, nose, hands and feet), the remaining part of the trinket dish has a matte finish. Use the mold therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a completely glossy trinket dish, but you can use Resin for the glossy parts to create a  sparkling Gnome.

Silicone mold for a lovely cat, called Gary. Gary is 21 cm (8 1/4") wide and high and 2.5 cm (1") thick, which means that Gary can easily sit on its own.

Calling all cat lovers! Craft your purr-fect feline masterpiece with this 2.5 cm thick cat mold. Whether it’s a sleek black cat or a calico cutie, your creations will stand tall and proud on a dressoir or table. A meow-some addition to any creative project!

Oh, Gary has a friend, a cute dog, and they get along very well, as shown in one of the pictures (for illustrative purposes, this item is only for the cat mold).

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) cat, it will have a matte finish.

Silicone mold for a set of 6 large Christmas Baubles with engraved Gnomes. Each bauble is 10 cm (4") wide and 8 mm (1/3") thick. There are three different patterns in the mold, two of each.

We have 4 more Christmas Bauble molds of the same size available (which are 6 mm thick), with holographic color effects, with druzy crystal patterns, with raised decorative patterns and with a smooth surface.

Silicone mold for a Holographic Tealight Candle Holder with decorative corners. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The decoration is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

This particular candle holder is our basic model, without any decoration, so you can use all your creativity to make a beautiful candle holder.

We have 10 more models in our collection available, some with Druzy crystal shapes, some with Holographic features and some with Decorative corners, A few of them are pictured in their finished state.

Silicone mold for a square tray with a 'Tetris' pattern. The tray is 28 x 28 cm (11" x 11") wide, 1 cm (2/5") thick and has a raised edge.

The tray is part of several molds with the 'Tetris' pattern, see the pictures (for illustrative purposes, this item is only for the tray mold).

Silicone mold for a large standing Nosy Rudolph. Rudolph is about 22.5 cm (8 9/10") wide and high and 2.5 cm (1") thick, excluding the raised eyes and nose.

Meet Nosy Rudolph, the quirky reindeer on a mission to find Santa! The handcrafted Christmas decoration that you can create with this mold, adds a playful touch to any table, dresser or windowsill. Get creative and make it a unique centerpiece for your holiday decoration!

!! ATTENTION: besides the eyes and nose, Rudolph doesn't have a glossy finish. Use the mold therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) Rudolph, it will have a matte finish. However, you can for instance use resin first for the eyes and nose, making them pop out on your finished creation.

Two silicone molds for:

• a set of two Tube coasters. The coasters are 12.5 x 12.5 cm (5" x 5") wide and 1 cm thick.
• a Tube tray. The tray is 12.5 x 25 cm (5" x 10") wide and 1 cm (2/5") thick.

Both the coasters and the tray have a flat bottom and the top consists of 5 adjacent tubes. 

!! ATTENTION: these mold don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in shiny (glossy) coasters and tray, they will have a matte finish, as shown in the pictures.

The molds are also available separately.

Silicone mold for a large decorative Pumpkin tray, featuring a Spooky House with some menacing bats! The tray is 28 cm (11") wide, 27 cm (10 2/3") high and 8 mm (1/3") thick. The Spooky House design is 0.75 mm thick and it will be raised on the surface of the tray.

Start your Halloween decorations off on the right foot with this spooky-cool Pumpkin tray! Featuring a large Halloween pumpkin, with a spooky house and even a few bats, it will be a frightful sight and it's the perfect way to get you in the spooky spirit. Boo-tiful!

We also have another mold available for a large Halloween pumpkin tray, featuring a Tombstone Zombie.

Silicone mold for 7 Holographic Halloween Pumpkin keychains. The pumpkins are 6 mm (1/4") thick, 5.7 cm (2 1/4") wide and 6 cm (2 1/3") tall. Each pumpkin has its own engraved facial expression and the holographic color effect will transfer to the surface of your resin pumpkin keychains.

There are 2 other versions of the pumpkins available, both without a holographic color effect: a 'Halloween' version with engraved faces and a 'plain' version, without engraved faces. 

One of the pictures shows all 3 molds (for illustrative purposes, this item is only for the 'Holographic Halloween' pumpkin mold).