All molds

Silicone mold for a Wall hanging, decorated with some beautiful wrapped Christmas gifts. The hanging has a diameter of 25 cm (10") and it is 8 mm (1/3") thick. The raised decorative pattern has a thickness of 0.75 mm. The decoration is only part of the hanging, leaving enough room to add a personal text or other decoration.

Deck your hall or porch with a one-of-a-kind Christmas wall hanging! This mold allows you to create and customize your own holiday decoration with text and creativity. Spread some festive cheer and make your walls stand out with your unique and playful piece. (Ho ho ho optional but highly recommended!)

We also have another Christmas wall hanging mold available, decorated with Santa Claus flying through the sky.

Silicone mold for two Tube coasters. The coasters are 12.5 x 12.5 cm (5" x 5") wide and 1 cm (2/5") thick. The coasters have a flat bottom and the top consists of 5 adjacent tubes.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) set of coasters, they will have a matte finish, as shown in the pictures.

We also have a mold available for a matching Tube tray, see one of the pictures (for illustrative purposes, this item is only for the Tube coasters mold). Both molds are also available as a set, for a special setprice.

Silicone mold for a Trinket Dish in the shape of a Clover leaf. The Clover leaf is 25.5 x 25.5 cm (10" x 10") wide and it has two layers. The baselayer is 8 mm (1/3") thick and the raised edge around the compartments is 6 mm (1/4") high. The dish is in total 14 mm (just over 1/2") thick and each compartment of the Clover is appr. 11 x 11 cm (appr. 4 1/3" x 4 1/3 ") wide.

The raised edge is along the entire side 5 mm (1/5") narrower than the baselayer, giving the Clover leaf dish an elegant appearance! And because of the 4 compartments you can use the dish also as a serving tray!

There is also a Trinket Dish mold available in the shape of an Oak leaf. Other available molds for trinket dishes have an ovalish shape.

Silicone mold for a square tray with a rough tumbled marble look and feel. The tray is 20 x 20 cm (8" x 8") wide and 1 cm (2/5") thick.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) tray, it will have a matte finish.

We also have a mold available for a 30 x 30 cm (XL) tumbled marble tray and a mold for 4 square tumbled marble coasters, see one of the pictures (for illustrative purposes, this item is only for the 20 x 20 cm tumbled marble tray mold).

Silicone square inlay mold with a decorative lead glass 'Daisy bud' pattern. The mold is 23 x 23 cm (9" x 9") wide and 5 mm (1/5") thick. The 'Daisy bud' pattern is 0.75 mm deep.

This inlay mold will make a great combination together with our 25 x 25 cm (10" x 10") large tray molds of 1 cm (2/5") and 2 cm (4/5") thickness, as shown in one of the pictures (resin artist: Resin Kreativwelt). Using the two molds together will create a tray with a raised edge of 5 mm (1/5").

There is also a smaller holographic version of this inaly mold available and we also have 8 mm (1/3") tray molds with this 'Daisy bud' pattern available, in a normal and in a holographic version.

Silicone mold for a Christmas themed winebutler for 6 glasses.

The winebutler has 2 layers, one layer is 8 mm (1/3") thick and the second layer, which is a Christmas wreath, is only 0.75 mm (1/34") thin. The Christmas wreath will be raised on the surface of the winebutler.

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

You can find Little Thumper not only on these two molds, he also appears on molds for a large tray, a set of 8 medallions, a tealight candle holder, a flower arranger and an egg holder tray. Everything you need to decorate a table for an Easter breakfast or Easter brunch!

Silicone mold for a holder for the Mandala Jerusalema coasters. 

The baseplate of the holder is engraved with the 'Mandala Jerusalema' and especially designed for the coaster set with the same engraving, see the pictures (for illustrative purposes, this item is only for the holder mold).

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The holder mold is part of our 'Mandala Jerusalema' design line, in which besides this mold are also a small and medium sized tray, a set of four coasters and a set of 8 medallions, as shown in some of the pictures (for illustrative purposes, this item is only for the holder mold).

The holder mold and coaster mold are also as a set available, for a special setprice.

Silicone inlay mold with an engraved 'Mermaid circles' pattern. The mold is 19.8 cm (7 4/5 ") wide and no less than 5.5 mm (1/5") thick, with a straight edge. Therefore it's quite easy to make a tray with raised edge when this inlay mold is used in another larger and deeper round(ish) mold.

There are also two other sizes available, 15.5 cm (6 1/10") and 24 cm (9 2/5").

Silicone mold for a large cake stand, engraved with the Peacock Mandala. The cake stand is 30 cm (11 4/5") wide and 8 mm (1/3") thick. The center has a hole of 6 mm (1/4") for the cakestand hardware, so no need to drill a hole.

The large cake stand mold is part of our 'Peacock Mandala' design line, in which besides this mold are also two smaller cake stands (to make a 2-tier or 3-tier cake stand), a set of four coasters, a coaster holder and a mold for 8 medallions.

This mold is also available in several sets, for a special setprice. 

Silicone mold for a small cake stand, engraved with the Peacock Mandala. The cake stand is 18 cm (7") wide and 8 mm (1/3") thick. The center has a hole of 6 mm (1/4") for the cakestand hardware, so no need to drill a hole.

The small cake stand mold is part of our 'Peacock Mandala' design line, in which besides this mold are also two larger cake stands (to make a 2-tier or 3-tier cake stand), a set of four coasters, a coaster holder and a mold for 8 medallions.

This mold is also available in several sets, for a special setprice. 

Create elegant resin pieces with this handmade Large Cobble Tray silicone mold. The mold produces a generous 25 × 25 cm tray with a soft, flowing silhouette and smooth polished finish, giving every casting a modern and organic look.

Its asymmetrical cobble-inspired shape makes this mold ideal for contemporary home décor, statement trays and decorative centrepieces. The broad casting surface leaves plenty of room for creative techniques such as colour effects, botanical inclusions, metallic accents, terrazzo-style designs or clean minimalist finishes.

This large silicone tray mold for resin is perfect for makers who want to create eye-catching functional pieces with a natural, sculptural appearance. The finished tray works beautifully as a decorative display tray, serving piece, centrepiece or handmade home accessory.

Each mold is handmade in our own workshop in the Netherlands using premium silicone and is designed for repeated casting.

Create three spooky Halloween door hangers with this handmade silicone mold featuring three unique engraved designs. The set includes a witch’s broom, a stack of smiling pumpkins and a magical potion bottle filled with sweet treats, giving you three playful seasonal designs from one mold.

The engraved details are perfect for experimenting with bold Halloween colours, metallic pigments, glitter, transparent effects or glow-in-the-dark accents. Each finished piece has its own character, making this Halloween door hanger silicone mold ideal for decorating doors, creating seasonal signs or making handmade Halloween gifts.

The long, narrow shape works beautifully as a hanging decoration, while the detailed designs make every casting instantly recognisable as part of a fun Halloween collection.

We also offer a second Halloween Door Hangers mold with three additional designs, allowing you to expand the collection and create even more seasonal variations.

Each mold is handmade in our own workshop in the Netherlands using premium silicone and is designed for repeated casting.

Set of two silicone molds for a small and a medium size Lavatera Flower tray. The small tray is 17.5 cm (6 9/10") wide and 16 cm (6 3/10") high, the medium size tray is 22.5 cm (8 9/10") wide and 20.5 cm (8") high. Both trays are 8 mm (1/3") thick.

This two-piece mold set combines the small and medium Lavatera trays, giving you even more ways to create with this elegant floral design. The subtle engraving adds depth to the petals while still leaving plenty of room for your own colours and effects. Use the trays separately for coordinated decorative pieces or combine them to build a beautiful two-tier cake stand. Two sizes, one graceful flower and endless creative possibilities.

These two molds are part of our Lavatera Flower Collection, which includes three different tray sizes, a mold for four Lavatera coasters and several carefully selected mold sets.

Silicone mold for four Poppy-shaped Coasters. The coasters are 12 cm (4 3/4") wide, 9 cm (3 1/2") high and 8 mm (1/3") thick. The petals are delicately engraved.

Say hello to your new favorite coaster set! Inspired by wild Blooming Poppies, this mold makes four elegant, poppy-shaped coasters, that will instantly add a floral flair to your home. Whether you go for soft pastel tones or bold reds and blacks, just like real poppies, the possibilities are endless. It's time to pour, play, and bloom!

The mold is part of our Poppy collection, which also includes a mold for 9 ornaments and two tray molds.

Silicone mold for a large Halloween Bat Hanger. The bat is 30 cm (12") wide, 12.5 cm (5") high and 8 mm (1/3") thick. The raised decorative pattern is 1 mm thick.

We also have 2 other Bat Hanger molds available, with a width of 20 cm (8") and 25 cm (10"), see one of the pictures (for illustrative purposes, this item is only for the large Bat Hanger mold).

The three molds are also available as a set, for a special setprice.

Silicone mold for a medium size Halloween Bat Hanger. The bat is 25 cm (10") wide, 10 cm (4") high and 8 mm (1/3") thick. The raised decorative pattern is 1 mm thick.

We also have 2 other Bat Hanger molds available, with a width of 20 cm (8") and 30 cm (12"), see one of the pictures (for illustrative purposes, this item is only for the medium size Bat Hanger mold).

The three molds are also available as a set, for a special setprice.

Silicone mold for a small Halloween Bat Hanger. The bat is 20 cm (8") wide, 8 cm (3 1/4") high and 8 mm (1/3") thick. The raised decorative pattern is 1 mm thick.

We also have 2 other Bat Hanger molds available, with a width of 25 cm (10") and 30 cm (12"), see one of the pictures (for illustrative purposes, this item is only for the small Bat Hanger mold).

The three molds are also available as a set, for a special setprice.