Holographic

Silicone mold for a set of four Holographic round coasters of 10 cm (4") wide and 8 mm (1/3") thick.

These coasters are the same as our normal round coasters, but then with a Holographic color effect, which  will transfer to the surface of your resin coasters. We call this specific effect 'Color Burst'!

We also have a mold separately available for a holographic round coaster holder, see one of the pictures (for illustrative purposes, this item is only for the coaster mold). 

Silicone mold for a set of 4 Holographic Fantasy coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.

These coasters are the same as our other Fantasy coasters, but then with a holographic color effect, which  will transfer to the surface of your resin coasters.

here are also molds available for a holographic Fantasy coaster holder and a holographic Fantasy tray, see one of the pictures (for illustrative purposes, this item is only for the holographic coasters mold). We also combined the 3 molds in 2 different available sets, for special setprices.

Two silicone molds for in total 12 Holographic Christmas ornaments (set #1 and #2). The ornaments are 5 mm (1/5") thick and between 6.5 cm (2 3/5") and 11 cm (4 1/3") high. The holographic color effect will transfer to the surface of your resin ornaments.

Both molds are also available separately. And we have the molds also in a non-holographic version available.

Silicone mold for a set of four Holographic square coasters of 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.

These coasters are the same as our normal square coasters, but then with a Holographic color effect, which  will transfer to the surface of your resin coasters. We call this specific effect 'Color Burst'!

The holographic coasters will fit in the holder for the normal square coasters, which is separately available.

Silicone mold for ..... a tray? Or a suncatcher? Or a decorative panel? Actually, this is a multipurpose Holographic silicone mold with a beautiful Tiffany-style Flower decoration. You can make a tray with it, or a suncatcher if you use transparent resin, or a decorative panel in front of a window or on a wall. Whatever you make, the endresult will look different at any time, from any angle, and with any (changing) lightsource.

The mold is 24.5 cm x 24.5 cm (9 3/5" x 9 3/5") wide and 6.5 mm (1/4") thick. The Tiffany-style flower pattern will be raised on the surface of the tray.

Silicone mold for a set of 4 Holographic Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick. The holder has a holographic color effect, which will transfer to the surface of your resin coasters.

The coaster mold is also available in a normal version, without the holographic effect.

There is also a Holographic holder mold available, see one of the pictures (for illustrative purposes, this item is only for the coasters mold). Both holographic molds are also as a set of 2 molds available, for a special setprice.

Silicone mold for 9 Holographic Christmas ornaments, in 3 different shapes: Balls, Stars and Bells. Each ornament is about 7.5 cm (3") wide and 8.5 cm (3 1/3") high. The ornaments are 6 mm (1/4") thick and they have a holographic color effect, that will transfer to the surface of your resin Christmas ornaments.

We also have a mold available for the same ornaments, but then without the holographic color effect.

Silicone mold for 26 Holographic letter tags. The tags are flower shaped, they have a decorative engraving and each letter has an engraved border, which makes it pop out beautifully. The letter tags have keyring holes, they are 5 cm (2") wide and 6 mm (1/4") thick. The holographic color effect will transfer to the surface of your resin tags.

As a bonus we added the same engraved  holographic flower in the center of the mold, it is about 11 cm (4 1/3") large.

There is also a similar mold available with 26 medallions that are not holographic and don't have keyring holes.

Silicone mold for a set of 6 large Holographic Christmas Baubles. Each bauble is 10 cm (4") wide, 6 mm (1/4") thick and they have a holographic color effect, that will transfer to the surface of your resin Christmas baubles.

We have 4 more Christmas Bauble molds of the same size available, with druzy crystal patterns, with raised decorative patterns, with engraved Gnomes (8 mm thick) and with a smooth surface.

Silicone mold for a set of 6 Holographic Decoration eggs, that can be used to decorate Easter branches and such. The eggs are 9 cm (3 1/2") tall and 6 mm (1/4") thick. The holographic color effect will transfer to the surface of your resin creations.

We also have molds for smaller and larger decoration eggs and a tray in our collection.

Silicone mold for 4 Holographic Geode coasters. The coasters are 12.5 cm (5") wide and 8 mm (1/3") thick. These coasters are the same as our normal round Geode coasters, but then with a holographic color effect, which  will transfer to the surface of your resin coasters.

There are also matching holographic molds for a coaster holder and a large tray, see one of the pictures (for illustratives purposes, this item is only for the coaster mold). We also combined the 3 molds in 2 different available sets, for special setprices.

Silicone mold for a Tealight Candle Holder, featuring a Holographic Color Burst. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for 6 Holographic Christmas ornaments. The ornaments are 5 mm (1/5") thick and between 7 cm (2 3/4") and 9.5 cm (3 3/4") high. The holographic color effect will transfer to the surface of your resin ornaments.

This mold is for set #2, there is also a set #1 available and both molds are also available as a set of 2 molds, for a special setprice. One of the pictures shows both molds (for illustrative purposes, this item is only for set #2).

We have this mold also in a non-holographic version available.

Silicone mold for a large Holographic Fantasy tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.

The mold has a holographic color effect, which  will transfer to the surface of your resin artwork.

We also have holographic Fantasy molds available for coasters, a coaster holder and medallions, as seen in one of the pictures (for illustrative purposes, this item is only for the holographic Fantasy tray mold).

Silicone mold for an oval Winebutler with a Holographic Broken Glass pattern. The holographic color effect will transfer into the resin, the end result depends on the colors and color combination that is used in the resin. The winebutler is 8 mm (1/3") thick.

The same design is also available in a smooth version, without pattern.

Set of 4 silicone Holographic Inlay molds, with a Flower engraved into them. Each inlay mold is 12.5 cm wide and appr. 3 mm (1/8") thick and they fit perfectly in our 15 cm (6") round molds (geode style, ribbed edge and basic round mold). 

The holographic color effect will transfer to the surface of your resin piece. Please be aware that when you pour a finishing (top) layer over the holographic piece, the holographic effect will be gone! We therefore advise not to use a top coat.

Silicone mold for 6 Holographic Christmas Star ornaments, with holes for a ribbon or cord. Each star is 10 cm (4") wide and high, 6 mm (1/4") thick and they have a holographic color effect, that will transfer to the surface of your resin Christmas ornaments.

We also have a mold available for the same ornaments, but then without the holographic color effect.

Silicone mold for 28 Holographic Domino stones. The stones are 24 mm x 50 mm (appr. 1" x 2") and 8 mm (1/3") thick.

The dots are hexagon shaped and the stones have a holographic finish that will transfer to the surface of your resin domino stones, giving you a beautiful display of colors!

We also have a non-holographic domino mold available, whose stones have a unique uneven surface.

Silicone mold for a large Holographic Geode tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.

The mold has a holographic color effect, which  will transfer to the surface of your resin artwork.

We also have matching holographic Geode molds available for coasters, a coaster holder and medallions, as seen in one of the pictures (for illustrative purposes, this item is only for the holographic Geode tray mold). The 3 molds are also available in 2 different sets, for special setprices.

Update: We now have the same holographic tray also in a smaller 18 cm (7") version available.

Silicone mold for 6 Holographic Christmas ornaments. The ornaments are 5 mm (1/5") thick and between 6.5 cm (2 3/5") and 11 cm (4 1/3") high. The holographic color effect will transfer to the surface of your resin ornaments.

This mold is for set #1, there is also a set #2 available and both molds are also available as a set of 2 molds, for a special setprice. One of the pictures shows both molds (for illustrative purposes, this item is only for set #1).

We have this mold also in a non-holographic version available.

Silicone mold for a Holographic Tealight Candle Holder with Rudolph the Red Nosed Reindeer. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. Rudolph is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a set of 4 Holographic Magical coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.

These coasters have the same shape as our other Magical coasters, but then with a holographic color effect, which  will transfer to the surface of your resin coasters.

There are also molds available for a holographic Magical coaster holder and a holographic Magical tray, see one of the pictures (for illustrative purposes, this item is only for the holographic coasters mold). We also combined the 3 molds in 2 different available sets, for special setprices.

This mold is also available in a normal version, wihout the holographic color effect.