All molds

Silicone mold for an Art panel, titled Horizon. The panel is 20 x 20 cm (8"x 8") wide and 15 mm (3/5") thick. 

Add an artistic touch to your interior with our 'Horizon' Wall Art Panel. Perfect for elevating any interior (wall) decoration, this mold allows you to unleash your creative side. Don't settle for boring walls, express yourself and create a unique addition to your home!

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available to create (wall) Art panels, some of them are shown in one of the pictures (for illustrative purposes, this item is only for the 'Horizon' mold). These panels all have the same width of 20 x 20 cm and thickness may vary.

Silicone mold for a square Holographic tray with a decorative lead glass 'Daisy bud' pattern. The surface of the tray has a holographic finish, which will result in beautiful shifting color effects on your resin tray.

The tray is 24.5 cm x 24.5 cm (9 3/5" x 9 3/5") wide and in total almost 9 mm (1/3") thick. The 'Daisy bud' pattern is 0.75 mm thick and it will be raised on the surface of the tray.

There is also a normal version of the same tray design available, without the holographic color effects. And both versions of this 'Daisy bud' pattern are also available as 5 mm (1/5") thick inlay molds, for our 1 cm and 2 cm deep square tray molds.

Three silicone molds for:

• a set of four square coasters with an engraved Ocean theme. The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
  
• a holder for the Ocean coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a square Ocean tray. The tray is 25 x 25 cm (10" x 10") and 8 mm (1/3") thick.

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The figures in these molds present themself also in a large 30 cm (12") Christmas tray and in 12 cute Christmas ornaments, for which we have molds available separately.

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Besides these two molds there are also Lily molds available for a set of 8 medallions and a tray of 25 cm (10"), as shown in one of the pictures (for illustrative purposes, this item is only for the coaster and holder mold).

Silicone inlay mold with a Honeycomb engraving. The size of the inlay mold is 26 x 30 cm ( 10 1/5" x  11 4/5") and it is appr. 4 mm (1/6") thick.

The inlay is specifically matched to the size of our Large 31 cm (12 1/8") Hexagon tray (item MOSH0193) and the thickness of this inlay mold makes it easy to create a tray with raised edge, by using this large tray mold.

The same design inlay mold is also available for the 23 cm (9") medium Hexagon tray and there is a holographic inlay mold for the medium sized Hexagon tray as well, as shown in one of the pictures (for illustrative purposes, this item is only for the Large sized honeycomb inlay mold).

Silicone mold for a small 'Fantasy' cake stand. The cake stand is 18 cm (7 1/2") wide and 8 mm (1/3") thick. The center has a hole of 6 mm (1/4") for the cakestand hardware, so no need to drill a hole.

This mold is one of our molds with the Fantasy theme, which further consists of a coaster mold, a coaster holder, 4 trays, one larger cakestand and a set of 8 medallions.

We made several of these molds in sets available, for special setprices.

Two silicone molds for a large 2-tier cake stand, engraved with the Peacock Mandala. The cake stands are 24 cm (9 2/5") and 30 cm (11 4/5") wide and 8 mm (1/3") thick. The centers have a hole of 6 mm (1/4") for the cakestand hardware, so no need to drill a hole.

The molds are part of our 'Peacock Mandala' design line, in which besides these molds are also a smaller cake stand (to make a 3-tier cake stand), a set of four coasters, a coaster holder and a mold for 8 medallions.

Silicone mold for a medium sized cake stand, engraved with the Peacock Mandala. The cake stand is 24 cm (9 2/5") wide and 8 mm (1/3") thick. The center has a hole of 6 mm (1/4") for the cakestand hardware, so no need to drill a hole.

The medium sized cake stand mold is part of our 'Peacock Mandala' design line, in which besides this mold are also a smaller and a larger cake stand (to make a 2-tier or 3-tier cake stand), a set of four coasters, a coaster holder and a mold for 8 medallions.

This mold is also available in several sets, for a special setprice. 

Silicone mold for an XL Flower Tray, shaped as a Poppy. The tray is 35.5 cm (14") wide, 27.5 cm (10 4/5") high and 8 mm (1/3") thick. The petals are delicately engraved.

Go big and let your creativity bloom! The XL Poppy Tray is a showstopper. Measuring an impressive 14" wide, this oversized floral beauty gives you all the space you need to go wild with color, texture, and imagination. Whether you're creating an eye-catching centerpiece, a dazzling serving tray, or a breathtaking piece of wall art, this mold gives you the canvas to make a serious statement.

The mold is part of our Poppy collection, which also includes molds for coasters, for 9 ornaments and for two smaller trays.

Silicone mold for an Art panel, titled Parallel Tubes. The panel is 20 x 20 cm (8"x 8") wide and can maximum be 19 mm (3/4") thick. 

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We also have another, similar, Tubes mold avalable, but then with diagonal tubes. both molds are also available as a set, for a special setprice.

Set of 2 silicone molds for Art panels, titled Dunes. Both panels are 20 x 20 cm (8"x 8") wide and they can maximum be 18 mm (7/10") thick. 

Make a statement! This set of Dunes I and Dunes II molds offers a seamless, serene flowing sand dunes pattern that can be spread across your entire wall. Ideal for those looking to create a large, impactful wall decoration. The matte finish makes them perfect for Jesmonite and similar products, allowing you to capture both the texture and natural beauty of sand dunes perfectly.

Both molds are also available separately.

!! ATTENTION: these molds don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in shiny (glossy) panels, they will have a matte finish.

We  also have other molds available for (wall) Art panels, these panels all have the same width of 20 x 20 cm and thickness may vary.

Three silicone molds for:

• 4 Oval coasters. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and 8 mm (1/3") thick. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide and 1 cm (2/5") thick.

Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.

There is also a mold available for an XL oval tray and all molds are also available engraved with thin 'Graceful lines'.

Silicone mold for a holder for Oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, 8 mm (1/3") thick and it can hold 4 of our oval coasters.

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

There are also molds for matching coasters and for two oval trays available, see one of the pictures (for illustrative purposes, this item is only for the oval holder mold).

We have the molds also in two sets available (coasters with holder, coasters with holder and large tray), for special setprices.

There is also a mold available for the same size oval coaster holder, but then engraved with thin 'Graceful lines'.

Silicone mold for a large Flower Arranger. This Flower Arranger is 27.5 cm (11") wide, 8 mm (1/3") thick and it has a whopping 21 holes in 3 different sizes.

Fun times and flower power await with the large Flower Arranger that you can create with this mold! Your Flower Arranger will hold up at least 21 stems perfectly, making it a breeze - and a beautiful sight - to arrange your favourite flowers into show-stopping bouquets. So go ahead, get creative and let your inner floral designer shine!

If you only have small vases, don't worry, we also have two molds for smaller Flower Arrangers in our collection, one with 5 holes and one with 9 holes.

Silicone mold for a square tray with an engraved Ocean theme. The tray is 25 x 25 cm (10" x 10") and 8 mm (1/3") thick.

There are also molds available for matching coasters and a coaster holder, see one of the pictures (for illustration purposes, this item is only for the tray mold).

The 3 molds are also in two different sets available (coasters with holder, coasters with holder and tray), for special setprices.

Silicone mold for a Holographic holder for 4 (holographic) Magical coasters. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Magical coasters, see one of the pictures (for illustrative purposes, this item is only for the holder mold). Both holographic molds are also as a set of 2 molds available, for a special setprice.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is also available in a normal version, without the holographic color effect.

Silicone mold for a holder for the Mandala Dahlia coasters.

The baseplate of the holder is engraved with the 'Mandala Dahlia' and especially designed for the coaster set with the same engraving, see the pictures (for illustrative purposes, this item is only for the holder mold).

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The holder mold is part of our 'Mandala Dahlia' design line, in which besides this mold are also a large tray, a set of four coasters and a set of 8 medallions, as shown in some of the pictures (for illustrative purposes, this item is only for the holder mold).

The holder mold and coaster mold are also as a set available, for a special setprice.

Silicone mold for a Holographic holder for 4 (holographic) Oriental coasters. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Oriental coasters, see one of the pictures (for illustrative purposes, this item is only for the holder mold). Both holographic molds are also as a set of 2 molds available, at a special setprice.

The legs of the holder are 44 mm (1 3/4") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is also available in a normal version, without the holographic color effect.

Silicone mold for an Art panel, titled Dunes II. The panel is 20 x 20 cm (8"x 8") wide and can maximum be 18 mm (7/10") thick. 

Bring nature into your home with this panel mold! As our other Dunes panel mold (Dunes I), this mold too features a similar serene flowing sand dunes pattern. You can use the mold as a standalone piece, perfect for creating unique wall decor. The matte finish ensures a perfect texture when used with Jesmonite and similar products. 

However, did you know you can cover an entire wall by combining Dunes I and Dunes II? Pair this mold with our Dunes I mold (available separately), to create a continuous pattern across your wall, as you can see in some of the pictures. Both molds are also available as a set, for a special setprice.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available for (wall) Art panels, these panels all have the same width of 20 x 20 cm and thickness may vary.

Three silicone molds for:

• a set of four Slate coasters. The coasters are appr. 11 x 13 cm (4 1/3"x 5 1/10") and 6 mm (1/4") thick.
• a holder for the Slate coasters. 
• a large oval Slate tray. The tray is 30 cm x 22.5 cm (12" x 8 4/5") large and 8 mm (1/3") thick.

The edges of the coasters, holder and tray are coarsened, for that specific slate look and feel.

The molds have a smooth surface, the 'crushed ice' effect that is shown in one of the pictures, is made with some of our inlay molds, which are available separately.

Silicone mold for a holder for our Oriental coasters.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is one of our molds with the Oriental theme, which further consists of a coaster mold, 4 trays and a set of 8 medallions, see one of the pictures for some of them (for illustrative purposes, this item is only for the coaster holder mold).

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

The holder mold is also available in a Holographic version.