Kintsugi-Stil

Silicone mold for a set of four square Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.

There is also a matching Kintsugi coaster holder available, which holds 4 coasters, and for a 25 cm (10") square Kintsugi tray, see some of the pictures (for illustrative purposes, this item is only for the coaster mold).

The 3 molds are also in two sets available (coasters with holder, coasters with holder and tray), for special setprices.

Two silicone molds for:

• a set of four square Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
  
• a holder for the Kintsugi coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. You can fix the supports with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Three silicone molds for:

• a set of four square Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
• a holder for the Kintsugi coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a square Kintsugi tray. The tray is 25 x 25 cm (10" x 10") and 8 mm (1/3") thick.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

The molds are also available separately.

Silicone mold for a square Kintsugi tray (Kintsugi is the Japanese art of fixing broken pottery). The tray is 25 x 25 cm (10" x 10") and 8 mm (1/3") thick.

There are also matching molds for a set of four Kintsugi coasters and holder available, see some of the pictures (for illustration purposes, this item is only for the tray mold).

The 3 molds are also in two sets available (coasters with holder, coasters with holder and tray), for a special setprice.

Silicone mold for a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

There are also molds available for matching coasters, a coaster holder and an XL tray, all engraved with the same graceful line pattern.

This mold is together with the matching coaster mold and coaster holder mold also as a set of 3 molds available, for a special setprice, see one of the pictures (for illustrative purposes, this item is only for the large oval tray mold).

This tray mold is also available in a plain version.

Silicone mold for an XL Oval tray. The tray is 24 x 35 cm (9 2/5" x 13 3/4") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

There are also molds available for matching coasters, a coaster holder and a smaller tray, all engraved with the same graceful line pattern.

This tray is also available in a plain version.

Silicone mold for a set of 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.

There are also molds for a matching coaster holder and for two oval trays with the same graceful line pattern available, see one of the pictures (for illustrative purposes, this item is only for the oval coaster mold).

The molds are also in two sets available (coasters with holder, coasters with holder and large tray), for special setprices.

Silicone mold for a holder for Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. 

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Three silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.

Two silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

There are also molds available for two oval trays with the same graceful line pattern.

These two molds are together with the large oval tray 'Graceful lines' also as a set of 3 molds available, for a special setprice.

Silicone mold for a holder for Oval coasters 'Graceful lines'. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and it can hold 4 of our oval coasters. The baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines.

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).