Alle Formen

Two silicone molds for:

• a set of four round coasters with a 'Wild Water' effect on the surface. The coasters are 11.5 cm (4 1/2") wide and 9 mm (1/3") thick. 
• a large round tray with a 'Wild Water' effect on the surface. The tray is 30 cm (11 4/5") wide and 9 mm (1/3") thick.

Both molds are also available separately.

Add an artistic touch to your home with thesese 2 'Wild Water' molds. Create unique coasters and a large tray that are sure to make a splash with their wild water effect. Be bold and unleash your creativity with this ocean-inspired set.

Create a distinctive set of four square coasters with this handmade Tumbled Marble silicone mold. The rough, stone-like surface and softly irregular texture give every finished piece the appearance of naturally tumbled marble, making this mold perfect for modern, minimalist and organic home décor.

This mold is especially well suited for Jesmonite, Jesin, A1 and similar mineral-based casting materials, where the matte surface really comes into its own. The subtle stone texture creates a premium handmade look that works beautifully with neutral tones, terrazzo effects, pigments and natural colour combinations.

The coasters can be used on their own or combined with our matching Square Tumbled Marble Trays, available in two sizes, to create a coordinated collection for tables, interiors and handmade gift sets.

Each mold is handmade in our own workshop in the Netherlands using premium silicone and is designed for repeated casting.

Important: this mold does not have a glossy finish. Resin can be used, but the finished casting will remain matte rather than glossy.

Matching products: Square Tumbled Marble Tray molds are also available in 20 × 20 cm and 30 × 30 cm.

Three silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.

Silicone mold for a large heart that is perforated with 66 holes, evenly spaced along the edge of the heart. The heart is 25 cm (10") wide, 23 cm (9") high and 8 mm (1/3") thick.

Make your Love craft projects extra special with this perforated heart. It features 66 holes around the edge, perfect for all your fabric, ribbon, wicker and crochet projects. Unleash your imagination, see what surprises you discover and bring the love into your home decor with this perforated heart!

Silicone mold for a large Holographic Heart shaped tray. The tray is 30 cm (12") wide, 27.8 cm (11")  tall and 8 mm (1/3") thick.

The mold has a holographic color effect, which  will transfer to the surface of your resin artwork.

This same large tray mold is also available in a regular version, without the holographic color effect.

Silicone mold for a small Holographic Geode tray. The tray is 18 cm (7") wide and 8 mm (1/3") thick.

The mold has a holographic color effect, which  will transfer to the surface of your resin artwork.

We have the same holographic tray also in a larger 28 cm (11") version available.

Four silicone inlay molds for Round coasters. The molds are 9 cm (3 1/2") wide and they are a perfect match for our mold for 10 cm (4") round coasters. And because the inlay molds are appr. 4 mm (1/6") thick, your result will be a coaster with a raised edge and a beautiful engraved surface.

We also have a few other round inlay molds available with a different pattern, see one of the pictures.

And this 'Mikado' pattern is also available for square and hexagon coasters, see one of the pictures (for illustrative purposes, this item is only for the square inlay molds).

Four silicone inlay molds for Round coasters. The molds are 9 cm (3 1/2") wide and they are a perfect match for our mold for 10 cm (4") round coasters. And because the inlay molds are appr. 4 mm (1/6") thick, your result will be a coaster with a raised edge and a beautiful engraved surface.

We also have a few other round inlay molds available with a different pattern, see one of the pictures.

Silicone mold for an XL Cascade Pebble Tray. The extra large tray is 27.5 cm (10 4/5") wide, 33.5 cm (13 1/5") high and 9 mm (1/3") thick. 

The tray is made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the tray a unique cascade-like appearance.

There is also a Pebble coaster mold and a large Pebble tray mold available with the same cascade design.

Silicone mold for a set of four Cascade Pebble coasters. The coasters are 11 cm (4 1/3") wide, 13 cm (5 1/5") high and 9 mm (1/3") thick. 

The coasters are made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the coasters a unique cascade-like appearance.

There is also a large and an extra large Pebble tray mold available with the same Cascade design, see one of the pictures (for illustrative purposes, this items is only for the coasters mold). The large tray mold and this coaster mold are also available as a set, at a special price.

Silicone mold for a deep rectangular tray. The tray is 15 x 30 cm (6" x 12") and 2 cm (4/5") thick.

The tray mold is suitable for deep pour projects, like flower preservation.

Set of three silicone molds for our trays with the Magical theme. The trays are 15 cm (6"), 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These three molds are part of our molds with the Magical theme, which further consists of a coaster mold, a coaster holder mold, an XL tray and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Silicone mold for a coaster holder with ribbed edge. The holder can hold 4 coasters that are 10 cm (4") wide and 8 mm (1/3") thick and it is specifically designed for our round coasters with ribbed edges, but other round coasters of maximum 10 cm wide will fit too.

The legs of the holder are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Silicone mold for a Flower Arranger with a Holographic Broken Glass pattern. The Flower Arranger is 17 cm (6 2/3") wide and the holographic color effect will transfer to the surface of your resin flower arranger.

It's a known 'problem', you sometimes get a nice little bouquet of flowers, but you only have a vase that is too big to put them in. Then this Flower Arranger will be an outcome, because now you will be able to arrange the flowers nicely in that large vase.

This flower arranger mold has 9 holes and the same design is also available in a smooth version, without pattern (one of the pictures shows the smooth version 'in action').

There is also a 'Holo Broken Glass' version with 5 holes available.

Four silicone inlay molds for Round coasters. The molds are 9 cm (3 1/2") wide and they are a perfect match for our mold for 10 cm (4") round coasters. And because the inlay molds are appr. 4 mm (1/6") thick, your result will be a coaster with a raised edge and a beautiful engraved surface.

We also have a few other round inlay molds available with a different pattern, see one of the pictures.

Silicone mold for a holder for our coasters with a 'Tetris' pattern. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 6 mm (1/4") thick. You can fix the supports with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Silicone mold for a large Christmas Tray - 'Gingerbread House'. The House is 22.5 cm (8 4/5") high, 25 cm (10") wide and 8 mm (1/3") thick.

We also have 4 other (ornament) molds with the Gingerbread House available, varying in size from 7.5 cm (3") to 20 cm (8").

Silicone mold for a handsome dog, called George. George is 25 cm (10") wide and 20 cm (8") high. He is also 2.5 cm (1") thick, which means that George can easily stand on its own feet.

Unleash your creativity with this adorable dog mold! Standing tall and proud at 2.5 cm thick, this mold is perfec to use with Jesmonite, Jesin and similar creative materials. And whether you call him George or give him some other nice name, your handcrafted dog will sit pretty on any shelf or desk!

By the way, George has a playmate, a sweet cat, and they get along very well, as shown in one of the pictures (for illustrative purposes, this item is only for the dog mold).

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) dog, it will have a matte finish.

Silicone mold for a matte Art panel, titled Feathers. The panel is 20 x 20 cm (8"x 8") wide and 20 mm (4/5") thick.

Add an artistic touch to your interior with our 'Feathers' Wall Art Panel. Perfect for elevating any interior (wall) decoration, this mold allows you to unleash your creative side. Don't settle for boring walls, express yourself and create a unique addition to your home!

The feathers form a continuous pattern, allowing you to place multiple panels next to each other and/or on top of each other for a beautiful artwork.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available to create (wall) Art panels, some of them are shown in one of the pictures (for illustrative purposes, this item is only for the matte 'Feathers' mold). These panels all have the same width of 20 x 20 cm and thickness may vary.

Silicone mold for a Square tray of 20 x 20 cm (8" x 8") wide and 1 cm (2/5") thick.

We also have a square mold available in 25 x 25 cm (10" x 10") and 30 x 30 cm (12" x 12").