Produits

Silicone mold for a Holographic Tealight Candle Holder with the AUM (OHM/OM) symbol. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The symbol is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration, see the pictures. A few of them are pictured in their finished state.

Silicone mold for a Holographic Tealight Candle Holder with decorative corners. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The decoration is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Holographic Tealight Candle Holder with Rudolph the Red Nosed Reindeer. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. Rudolph is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder with the Holographic Yin Yang symbol. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The symbol is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration, see the pictures. A few of them are pictured in their finished state.

Tic-Tac-Toe is a game for 2 players who take turns marking the spaces in a 3×3 grid with an X or an O. The player who succeeds in placing three of their marks in a diagonal, horizontal or vertical row is the winner. It's a fun and not that easy game.

With this silicone mold you can make your own personalized Tic-Tac-Toe board game. The dimensions of the game board are 22 cm (8 2/3") x 16 cm (6 1/3") and it consists of 3 layers:

• a 1 mm (1/25") thin layer for the title of the game plus a divider
• a 6 mm (1/4") thick playing field layer (which includes a holder for the tenth game piece) 
• a 4 mm (1/6") thick baseplate layer.

The three layers makes it possible to vary endlessly with colored resin.

Silicone mold for a medium sized matte Tree of Life symbol. This Tree of Life is 20 cm (8") wide and 15 mm (3/5") thick.

The iconic Tree of Life symbolizes growth, balance and harmony. Use your artistic talents to create a beautiful and unique symbol, embrace your inner tree hugger and add a touch of whimsy to every room.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) Tree of Life, it will have a matte finish, as shown in some of the pictures.

We also have (a larger) Tree of Life mold available which has a glossy finish, perfect to use with epoxy resin.

Silicone mold for a large shiny Tree of Life symbol. This mold has two layers, a round base of 26.5 cm (10 2/5") wide and 8 mm (1/3") thick and the tree of life which is 25 cm (10") wide and 7 mm (3/10") thick. This makes the total symbol 26.5 cm (10 2/5") wide and 15 mm (3/5") thick.

The iconic Tree of Life symbolizes growth, balance and harmony. Use your artistic talents to create a beautiful and unique symbol, embrace your inner tree hugger and add a touch of whimsy to every room.

We also have (a smaller) Tree of Life mold available which has a matte finish, perfect to use with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders.

Silicone mold for a large Trinket Dish. The Trinket Dish is 15 x 30 cm (6" x 12") wide and it has two layers. The baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dish is in total 14 mm (just over 1/2") thick.

The raised edge is along the entire side 5 mm (1/5") narrower than the baselayer, giving the dish an elegant appearance!

There are also molds for a smaller and larger Trinket Dish available, see one of the pictures (for illlustrative purposes, this item is only for the large Trinket Dish). The three molds are also available in sets of two or three, for special setprices.

Silicone mold for a medium size Trinket Dish. The Trinket Dish is 12.5 x 25 cm (5" x 10") wide and it has two layers. The baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dish is in total 14 mm (just over 1/2") thick.

The raised edge is along the entire side 5 mm (1/5") narrower than the baselayer, giving the dish an elegant appearance!

There are two larger Trinket Dishes available, see one of the pictures (for illlustrative purposes, this item is only for the medium size Trinket Dish). The three molds are also available in sets of two or three, for special setprices.

Silicone mold for an XL Trinket Dish. The Trinket Dish is 17.5 x 35 cm (7" x 14") wide and it has two layers. The baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dish is in total 14 mm (just over 1/2") thick.

The raised edge is along the entire side 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

There are also molds for two smaller Trinket Dishes available, see one of the pictures (for illlustrative purposes, this item is only for the XL Trinket Dish). The three molds are also available in sets of two or three, for special setprices.

Silicone mold for two Tube coasters. The coasters are 12.5 x 12.5 cm (5" x 5") wide and 1 cm (2/5") thick. The coasters have a flat bottom and the top consists of 5 adjacent tubes.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) set of coasters, they will have a matte finish, as shown in the pictures.

We also have a mold available for a matching Tube tray, see one of the pictures (for illustrative purposes, this item is only for the Tube coasters mold). Both molds are also available as a set, for a special setprice.

Silicone mold for a Tube tray. The tray is 12.5 x 25 cm (5" x 10") wide and 1 cm (2/5") thick. The tray has a flat bottom and the top consists of 5 adjacent tubes.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) tray, it will have a matte finish, as shown in the pictures.

We also have a mold available for 2 matching Tube coasters, see one of the pictures (for illustrative purposes, this item is only for the Tube tray mold). Both molds are also available as a set, for a special setprice.

Silicone mold for 4 square coasters with a rough tumbled marble look and feel. The coasters are 10 x 10 cm (4" x 4") wide and 1 cm (2/5") thick.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) set of coasters, they will have a matte finish.

We also have two molds available for a square tumbled marble tray (20 x 20 cm and 30 x 30 cm), see one of the pictures (for illustrative purposes, this item is only for the tumbled marble coasters mold).

Silicone mold for a square tray with a rough tumbled marble look and feel. The tray is 20 x 20 cm (8" x 8") wide and 1 cm (2/5") thick.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) tray, it will have a matte finish.

We also have a mold available for a 30 x 30 cm (XL) tumbled marble tray and a mold for 4 square tumbled marble coasters, see one of the pictures (for illustrative purposes, this item is only for the 20 x 20 cm tumbled marble tray mold).

Silicone mold for a square XL tray with a rough tumbled marble look and feel. The tray is 30.5 x 30.5 cm (12" x 12") wide and 12.5 mm (1/2") thick.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) tray, it will have a matte finish.

We also have a mold available for a 20 x 20 cm square tumbled marble tray and a mold for 4 square tumbled marble coasters, see one of the pictures (for illustrative purposes, this item is only for the XL tumbled marble tray mold).

Silicone mold for an Art panel, titled Botanicum. The panel is 20 x 20 cm (8"x 8") wide and 15 mm (3/5") thick. 

Add an artistic touch to your interior with our 'Botanicum' Wall Art Panel. Perfect for elevating any interior (wall) decoration, this mold allows you to unleash your creative side. Don't settle for boring walls, express yourself and create a unique addition to your home!

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available to create (wall) Art panels, some of them are shown in one of the pictures (for illustrative purposes, this item is only for the 'Botanicum' mold). These panels all have the same width of 20 x 20 cm and thickness may vary.

Silicone mold for a matte Art panel, titled Feathers. The panel is 20 x 20 cm (8"x 8") wide and 20 mm (4/5") thick.

Add an artistic touch to your interior with our 'Feathers' Wall Art Panel. Perfect for elevating any interior (wall) decoration, this mold allows you to unleash your creative side. Don't settle for boring walls, express yourself and create a unique addition to your home!

The feathers form a continuous pattern, allowing you to place multiple panels next to each other and/or on top of each other for a beautiful artwork.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available to create (wall) Art panels, some of them are shown in one of the pictures (for illustrative purposes, this item is only for the matte 'Feathers' mold). These panels all have the same width of 20 x 20 cm and thickness may vary.

Silicone mold for a shiny Art panel, titled Feathers. The panel is 20 x 20 cm (8"x 8") wide and 15 mm (3/5") thick.

Add an artistic touch to your interior with our shiny 'Feathers' Wall Art Panel. Perfect for elevating any interior (wall) decoration, this mold allows you to unleash your creative side. Don't settle for boring walls, express yourself and create a unique addition to your home!

The feathers form a continuous pattern, allowing you to place multiple panels next to each other and/or on top of each other for a beautiful artwork.

This mold has a shiny finish, the same design is also available in a 20 mm thick mold with a matte finish, perfect to use with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders.

We  also have other molds available to create (wall) Art panels, some of them are shown in one of the pictures (for illustrative purposes, this item is only for the shiny 'Feathers' mold). These panels all have the same width of 20 x 20 cm and thickness may vary.

Silicone mold for an Art panel, titled Horizon. The panel is 20 x 20 cm (8"x 8") wide and 15 mm (3/5") thick. 

Add an artistic touch to your interior with our 'Horizon' Wall Art Panel. Perfect for elevating any interior (wall) decoration, this mold allows you to unleash your creative side. Don't settle for boring walls, express yourself and create a unique addition to your home!

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available to create (wall) Art panels, some of them are shown in one of the pictures (for illustrative purposes, this item is only for the 'Horizon' mold). These panels all have the same width of 20 x 20 cm and thickness may vary.

Silicone mold for an Art panel, titled Squares and Circles. The panel is 20 x 20 cm (8"x 8") wide, 18 mm (7/10") thick and all elements in the panel have different heights.

Add an artistic touch to your interior with our 'Squares and Circles' Wall Art Panel. Perfect for elevating any interior (wall) decoration, this mold allows you to unleash your creative side. Don't settle for boring walls, express yourself and create a unique addition to your home!

The elements in the panel form a symmetrical pattern, allowing you to place multiple panels next to each other and/or on top of each other for a beautiful artwork.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available to create (wall) Art panels, some of them are shown in one of the pictures (for illustrative purposes, this item is only for the 'Squares and Circles' mold). These panels all have the same width of 20 x 20 cm and thickness may vary.