Alle Formen

Silicone mold for 9 extra small Christmas Ornaments with a Happy Santa Claus. Each Santa is 7.5 cm (3") high and 6 mm (1/4") thick.

We also have 4 other Happy Santa molds available, varying in size from 10 cm (4") to 25 cm (10").

Silicone mold for a large Christmas Bauble Trinket Dish. The Trinket Dish is 21.5 x 22.5 cm (8 1/2" x 8 9/10") wide and 18 mm (7/10") thick, including a raised edge of 8 mm (1/3").

Looking for a festive way to stash your holiday treats? Look no further and create your own decorative Christmas dish with this mold! It will be perfect for holding your favorite candies and sweets (warning: may cause an increase in Christmas spirit!).

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) trinket dish, it will have a matte finish.

Two silicone molds for a medium size and a large round Trinket Dish. The medium Trinket Dish has a diameter of 18 cm (7") and the large Trinket Dish has a diameter of 23 cm (9").

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire disc 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Silicone mold for 7 Halloween Pumpkin keychains. The pumpkins are 6 mm (1/4") thick, 5.7 cm (2 1/4") wide and 6 cm (2 1/3") tall. Each pumpkin has its own engraved facial expression. 

There are 2 other versions of the pumpkins available, a 'holographic Halloween' version with engraved faces (the holographic color effect will transfer to the surface of your resin pumpkin keychains) and a 'plain' version, without engraved faces and without a holographic color effect. 

One of the pictures shows all 3 molds (for illustrative purposes, this item is only for the 'Halloween' pumpkin mold).

Two silicone molds for a large and an extra large Trinket Dish. The large Trinket Dish is 15 x 30 cm (6" x 12") wide and the extra large Trinket Dish is 17.5 x 35 cm (7" x 14") wide.

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire side 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Three silicone molds for Druzy Crystal Christmas ornaments, one with a Christmas tree, one with a Christmas star and one with a Cristmas bell. Each ornament is 15 cm (6") tall, 11 cm (4 1/3") wide and 6 mm (1/4") thick.

The molds are also available separately.

Silicone mold for a Christmas ornament with a Druzy Crystal Christmas tree. The ornament is 15 cm (6") tall, 11 cm (4 1/3") wide and 6 mm (1/4") thick.

We have 2 more Druzy Crystal ornament molds of the same size available, one with a Christmas star and one with a Christmas bell, see one of the pictures (for illustrative purposes, this item is only for the Crystal Christmas tree mold). The three ornament molds are also as a set of 3 molds available, for a special setprice.

Silicone mold for 2 large Christmas Angels. Each Angel is 20 cm (8") tall and 6 mm (1/4") thick.

We have 4 more Christmas Angel molds available, with angels varying in size from 5 cm (2") to 15 cm (6"). Some of them are also available in a Druzy crystal version.

Silicone mold for a small Holographic Fantasy tray. The tray is 18 cm (7") wide and 8 mm (1/3") thick.

The mold has a holographic color effect, which  will transfer to the surface of your resin artwork.

The same shape of this holographic tray is also available in a large size of 28 cm (11").

Silicone mold for a deep round disc. The disc is 17 cm (6 2/3") wide, 2 cm (4/5") thick and the mold has a smooth and shiny finish.

The disc mold is suitable for deep pour projects, like flower preservation. We also have a deep pour round mold available in 12 cm (4 3/4"), 22 cm (8 2/3") and in 27 cm (10 2/3").

Silicone mold for an XL Scallop tray. The tray is 33 cm (13") x 28.5 cm (11") and 8 mm (1/3") thick.

There are also Scallop molds available for a set of 4 coasters, a matching coaster holder / small tray, a large tray and for medallions, see one of the pictures (for illustrative purposes, this item is only for the XL tray mold).

Some of the scallop molds are also in two different sets available (coasters with holder, coasters with holder and the large tray), for special setprices.

Silicone mold for a large Hexagon tray. The tray is 31 cm (12 1/8") wide, measured from corner to opposite corner, and 8 mm (1/3") thick.

This tray mold is part of our line of Hexagon molds, in which besides this mold are also molds for a set of four coasters, a matching coaster holder, a smaller tray, a set of eight hexagon medallions and a set of eight hexagon napkin rings.

There is a special prized hexagon mold set available which has this tray, the mold for 4 hexagon coasters and the matching coaster holder, see one of the pictures.

Silicone mold for a holder for four coasters. It can hold four coasters which are maximum 6 mm (1/4") thick. The edge of the holder is coarsened and it is especially designed for our Slate coasters, for which we have a mold available too.

The holder mold and coaster mold are also as a set available, for a special setprice.

Set of 2 silicone molds for Wall Art panels. The panels are titled Parallel Tubes and Diagonal Tubes. Each panel is e panel is 20 x 20 cm (8"x 8") wide and they  can maximum be 19 mm (3/4") thick. 

!! ATTENTION: these molds don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in shiny (glossy) panels, they will have a matte finish.

The molds are also available separately.

BOO!

Silicone mold for 8 Halloween Ghost keychains. The ghosts are 6 mm (1/4") thick and 6 cm (2 1/3") tall. The width varies by ghost and each ghost has its own engraved facial expression.

The mold is also in a holographic version available (the holographic color effect will  transfer to the surface of your resin ghost keychains)!

Silicone mold for 10 Elegant Engraved Christmas Baubles. The smallest bauble is 6.5 cm (2 3/5") wide, the tallest bauble is 13 cm (5 1/8") tall. Each bauble is 6 mm (1/4") thick.

A beautiful mix of classic shapes and elegant engraved details makes this set perfect for stylish Christmas creations. Each bauble has its own distinctive design, giving you plenty of room to experiment with colours, glitter and festive inclusions. Use them as tree decorations, gift tags or handmade keepsakes for family and friends. 

With ten different designs in one mold, your Christmas collection will be anything but ordinary!

Silicone mold for 4 medium size Holographic Christmas Angels. Each Angel is 15 cm (6") tall, 6 mm (1/4") thick and they have a holographic color effect, that will transfer to the surface of your resin Christmas angels.

We also have a mold available for 6 Holographic Christmas Angels of 10 cm (4") each, see one of the pictures (for illustrative purposes, this item is only for the mold with 4 Christmas Angels).

Both molds are also available in a version without the holographic color effect and  in a version with druzy crystal Angel wings.

Silicone mold for an Art panel, titled Squares and Circles. The panel is 20 x 20 cm (8"x 8") wide, 18 mm (7/10") thick and all elements in the panel have different heights.

Add an artistic touch to your interior with our 'Squares and Circles' Wall Art Panel. Perfect for elevating any interior (wall) decoration, this mold allows you to unleash your creative side. Don't settle for boring walls, express yourself and create a unique addition to your home!

The elements in the panel form a symmetrical pattern, allowing you to place multiple panels next to each other and/or on top of each other for a beautiful artwork.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) panel, it will have a matte finish.

We  also have other molds available to create (wall) Art panels, some of them are shown in one of the pictures (for illustrative purposes, this item is only for the 'Squares and Circles' mold). These panels all have the same width of 20 x 20 cm and thickness may vary.

Silicone mold for 4 Halloween coasters, featuring a Spiderweb! And the spider is still in the web, hunting for a treat!

The coasters are 12.5 cm (5") wide and 8 mm (1/3") thick. The Webdesign is 0.75 mm thick and it will be raised on the surface of the coasters.

There is also a mold available for a large Spiderweb tray, with an even larger Spider, and both molds are also as a set available, see one of the pictures (for illustrative purposes, this item is only for the spiderweb coaster mold).

Silicone mold for a Square tray of 25 x 25 cm (10" x 10") wide and 1 cm (2/5") thick.

We also have a square mold available in 20 x 20 cm (8" x 8") and 30 x 30 cm (12" x 12").

Silicone mold for a large Rectangular Geode-style tray with rough sides. The tray is about 18 x 31 cm (7" x 12") wide and 12 mm (1/2") thick.

This mold for a Rough & Tough Rectangular tray is designed for the creative mind that likes it a little rough on the sides and smooth on the surface! The mold can be used with Resin and Acrylic Resin (Jesmonite, Acrylic One, Jesin and other brands). Made to look like a real stone tray, it's a beautiful mix of stylish and strong - perfect for all of your creativity and decoration needs. 

We also have other Rough & Tough molds available, for coasters and trays that all have the same beaten-up look and feel.

The Rough & Tough molds are also available in different sets of two molds, for special setprices.

Silicone mold for a large 'Merry Christmas' tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.

We also have a set of 3 molds available with this tray mold, the coaster mold and the coaster holder mold, see one of the pictures (for illustrative purposes, this item is only for the tray mold).