Sets

Set of 2 silicone molds for 4 Round Geode coasters and a matching holder. The coasters have the same shape as our round Geode trays, but then smaller, they are about 12.5 cm (appr. 5") wide and 8 mm (appr. 1/3") thick. The holder is specifically designed for these coasters.

The molds are also available seperately.

A set with these two molds and a mold for a large round Geode tray of 25 cm (10") is available as well, see one of the pictures (for illustratives purposes, this item is only for the coaster and holder mold).

You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Both molds are also in a holographic version available, for spectacular color effects on the surface of your resin coasters and holder!

Set of 3 silicone molds for 4 Round Geode coasters with a matching holder and a large round Geode Tray. The coasters have the same shape as the tray and they are about 12.5 cm (appr. 5") wide and 8 mm (appr. 1/3") thick. The holder is specifically designed for these coasters. The Geode tray is 25 cm (10") wide and 10 mm (2/5") thick. 

You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The molds are also separately available.

Two silicone molds for:

• a set of two round coasters with rough sides. The coasters have a diameter of 12.5 cm (5") and they are 12 mm (1/2") thick. The flat surface of each coaster is about 9 cm (3 1/2"). 
• a round tray with rough sides. The tray has a diameter of 22.5 cm (9") and it is 12 mm (1/2") thick.

These two molds are thick and rough, and still have a shiny surface! Perfect to create a rock-solid set of coasters and tray that will be a beautiful decoration on any table. With your creativity and inspiration, the possibilities with Resin and Acrylic Resin are endless. Don't be afraid to get rough and tough with these molds, let your imagination run wild!

We also have other Rough & Tough molds available, for coasters and trays that all have the same beaten-up look and feel.

Set of two silicone molds for four irregular shaped Geode coasters and a matching holder. The Coasters are approx. 12.5 cm (5") wide and 10 mm (2/5") thick. The holder is 10 mm (2/5") thick.

Cure your thirst for something original with this set of 2 molds! The Geode coasters mold has an irregular shape and it comes with a holder mold, making it a unique set. Your guests won't be able to resist the 'rock'ing atmosphere! ;)

The molds are also available separately.

Two silicone molds for:

• 4 coasters in the shape of a Pumpkin. The coasters are 12.5 cm (5") wide, 12 cm (4 3/4") tall and 8 mm (1/3") thick.
• a large Pumpkin tray. The tray is 28 cm (11") wide, 27 cm (10 2/3") tall and 8 mm (1/3") thick.

Make your Halloween spooktacular with these 2 molds, perfect for adding a touch of autumnal fun to your seasonal decorations. Trick or treat!

The molds are also available separately.

Set of 2 Holographic silicone molds for 4 Geode coasters and a matching holder. The coasters are 12.5 cm (5") wide and 8 mm (1/3") thick. The holder is specifically designed for these coasters and both molds have a holographic color effect, which  will transfer to the surface of your resin coasters.

The molds are also available separately.

You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Three silicone molds for a large 3-tier cake stand, engraved with the Peacock Mandala. The cake stands are 18 cm (7"), 24 cm (9 2/5") and 30 cm (11 4/5") wide and 8 mm (1/3") thick. The centers have a hole of 6 mm (1/4") for the cakestand hardware, so no need to drill a hole.

The molds are part of our 'Peacock Mandala' design line, in which besides these molds are also a set of four coasters, a coaster holder and a mold for 8 medallions.

Two silicone molds for a medium size and a large Trinket Dish. The medium Trinket Dish is 12.5 x 25 cm (5" x 10") wide and the large Trinket Dish is 15 x 30 cm (6" x 12") wide.

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire side 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Two silicone molds for:

• a set of two Tube coasters. The coasters are 12.5 x 12.5 cm (5" x 5") wide and 1 cm thick.
• a Tube tray. The tray is 12.5 x 25 cm (5" x 10") wide and 1 cm (2/5") thick.

Both the coasters and the tray have a flat bottom and the top consists of 5 adjacent tubes. 

!! ATTENTION: these mold don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in shiny (glossy) coasters and tray, they will have a matte finish, as shown in the pictures.

The molds are also available separately.

Double, double toil and trouble, fire burn and cauldron bubble! (William Shakespeare)

Two silicone molds for:

• 4 coasters in the shape of a Whitch's Cauldron!! The coasters are 12.5 cm (5") wide, about 10 cm (4") high and 8 mm (1/3") thick.
• a large Whitch's Cauldron tray. The tray is 30 cm (12") wide, about 24 cm (9 1/3") high and 8 mm (1/3") thick.

The coasters and tray will be beautiful as Halloween decoration. The molds are also available separately.

Three silicone molds for Druzy Crystal Christmas ornaments, one with a Christmas tree, one with a Christmas star and one with a Cristmas bell. Each ornament is 15 cm (6") tall, 11 cm (4 1/3") wide and 6 mm (1/4") thick.

The molds are also available separately.

Three silicone molds for:

• a set of four Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick.
• a holder for the Hexagon coasters. The holder is large enough for hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. You can fix the six legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Hexagon tray. The tray is 31 cm (12 1/8") wide, measured from corner to opposite corner, and 8 mm (1/3") thick.

Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.

Set of three silicone molds for our trays with the Magical theme. The trays are 15 cm (6"), 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These three molds are part of our molds with the Magical theme, which further consists of a coaster mold, a coaster holder mold, an XL tray and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Two silicone molds for:

• 28 Domino stones. These are special stones because the dots are hexagon shaped and the surface of the stones is uneven, which gives each stone a unique look! The stones are 24 mm x 50 mm (appr. 1" x 2") and about 6 mm (1/4") thick.
• a tray to store the 28 Domino stones, to better prevent them from getting lost. The dimensions of the tray are 21 cm x 25 cm (8 1/3" x 10") and it is in total 1 cm (2/5") thick. The tray has two layers, one for the decorative border, which is 6 mm (1/4") thick and a second layer of 4 mm (1/6") for the baseplate. The baseplate has a decorative pattern engraved into it.

Three silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
• a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.

Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.

Set of two silicone molds for our trays with the Magical theme. The trays are 15 cm (6") and 20 cm (8") wide and 8 mm (1/3") thick.

These two molds are part of our molds with the Magical theme, which further consists of a coaster mold, a coaster holder, 2 larger trays and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.