Coasters

Silicone mold for a set of four round coasters of 10 cm (4") wide and 8 mm (1/3") thick. There is also a mold available for a holder, see one of the pictures (for illustrative purposes, this item is only for the coaster mold).

 Need more than four coasters in the holder? Then get the mold for longer legs too, so that eight coasters will fit into the holder.

It is also easy to make round coasters with a raised edge and an engraved pattern if you combine this mold with one of our round inlay molds.

The round coaster mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a set of four 'Fantasy' coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.

This mold is one of our molds with the Fantasy theme, which further consists of a coaster holder, 4 trays, 2 cakestands and a set of 8 medallions.

Several of these molds are in sets available, for special setprices. 

The Fantasy coaster mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a set of four Holographic round coasters of 10 cm (4") wide and 8 mm (1/3") thick.

These coasters are the same as our normal round coasters, but then with a Holographic color effect, which  will transfer to the surface of your resin coasters. We call this specific effect 'Color Burst'!

We also have a mold separately available for a holographic round coaster holder, see one of the pictures (for illustrative purposes, this item is only for the coaster mold). 

Silicone mold for a set of four square coasters of 10 x 10 cm (4") and 8 mm (1/3") thick. There is also a mold available for a holder, see one of the pictures (for illustrative purposes, this item is only for the coaster mold).

Need more than four coasters in the holder? Then get the mold for longer legs too, so that eight coasters will fit into the holder.

It is also easy to make square coasters with a raised edge and an engraved pattern if you combine this mold with one of our square inlay molds.

The square coaster mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a set of four square Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.

There is also a matching Kintsugi coaster holder available, which holds 4 coasters, and for a 25 cm (10") square Kintsugi tray, see some of the pictures (for illustrative purposes, this item is only for the coaster mold).

The 3 molds are also in two sets available (coasters with holder, coasters with holder and tray), for special setprices.

Silicone mold for 4 round Geode coasters. The coasters have the same shape as our round Geode trays, but then smaller, they are 12.5 cm (5") wide and 8 mm (1/3") thick. There is also a mold for a matching coaster holder.

This item is only for the coaster mold, but both the coaster and holder mold are as a set available, for a special setprice.

A set with this coaster mold, the holder mold and a mold for a large round Geode tray of 25 cm (10") is available as well, see one of the pictures (for illustratives purposes, this item is only for the coaster mold).

(Please note that these coasters are not the same as our irregular shaped Geode coasters (item MOSH0054) and they will not fit in the holder for the irregular coasters.)

The Geode coaster mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a set of 4 Holographic Fantasy coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.

These coasters are the same as our other Fantasy coasters, but then with a holographic color effect, which  will transfer to the surface of your resin coasters.

here are also molds available for a holographic Fantasy coaster holder and a holographic Fantasy tray, see one of the pictures (for illustrative purposes, this item is only for the holographic coasters mold). We also combined the 3 molds in 2 different available sets, for special setprices.

Silicone mold for two square Geode-style coasters with rough sides. The coasters are about 12.5 x 12.5 cm (5" x 5") wide and 12 mm (1/2") thick. The flat surface of each coaster is about 9 x 9 cm (3 1/2" x 3 1/2").

Keep your tables safe from water rings in style with this Rough & Tough Square Coaster duo! Beaten up on the sides, but smooth and shiny on the top, the coasters made with this mold are solid as a rock.

The mold includes two cool Geode-style thick coasters and it's perfect for both Resin and Acrylic resin (Jesmonite, Acrylic One, Jesin and other brands). Don't be fooled by their toughness, these coasters will be sure to brighten up your space!

We also have other Rough & Tough molds available, for coasters and trays that all have the same beaten-up look and feel.

The Rough & Tough molds are also available in different sets of two molds, for special setprices.

Silicone mold for a set of 4 Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick.

This coaster mold is part of our line of Hexagon molds, in which besides this mold are also molds for a matching coaster holder, two hexagon trays, a set of eight hexagon medallions and a set of eight hexagon napkin rings.

There are two special prized hexagon sets of 3 molds available with this coaster mold, one set with the holder and the medium sized hexagon tray and one set with the holder and the large hexagon tray.

It is also easy to make Hexagon coasters with a raised edge and an engraved pattern if you combine this mold with one of our Hexagon inlay molds.

The Hexagon coaster mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a set of 4 Cup Coasters. The coasters are 12.5 cm (5") wide, 9 cm (3 1/2") high and 8 mm (1/3") thick.

There are also molds available for a 25 cm (10") large Cup tray and a 35.5 cm (14") XL Cup tray, see one of the pictures (for illustrative purposes, this item is only for the cup coasters mold).

This cup coasters mold and the large cup tray mold are also available as a set, at a special setprice.

Silicone mold for two Geode coasters with Rough sides. The coasters are about 14 x 11.5 cm (5 1/2" x 4 1/2") wide and 12 mm (1/2") thick. 

Our Rough & Tough Geode Coaster mold isn’t for the faint of heart! The coasters are thick, tough and designed to look and feel like genuine rough-cut Geode slices. Featuring 12 mm (1/2") of thickness, these rock star coasters will protect your table from water rings all night long. Show off your rough side with these striking coasters!

We also have other Rough & Tough molds available, for coasters and trays that all have the same beaten-up look and feel.

The Rough & Tough molds are also available in different sets of two molds, for special setprices.

Silicone mold for a set of four Holographic square coasters of 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.

These coasters are the same as our normal square coasters, but then with a Holographic color effect, which  will transfer to the surface of your resin coasters. We call this specific effect 'Color Burst'!

The holographic coasters will fit in the holder for the normal square coasters, which is separately available.

Silicone mold for a set of 4 Holographic Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick. The holder has a holographic color effect, which will transfer to the surface of your resin coasters.

The coaster mold is also available in a normal version, without the holographic effect.

There is also a Holographic holder mold available, see one of the pictures (for illustrative purposes, this item is only for the coasters mold). Both holographic molds are also as a set of 2 molds available, for a special setprice.

Silicone mold for a set of four 'Magical' coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.

This mold is one of our molds with the Magical theme, which further consists of a coaster holder mold, 4 trays and a set of 8 medallions, see one of the pictures (for illustrative purposes, this item is only for the coasters mold).

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

This mold is also available in a Holographic version.

Silicone mold for a set of four coasters, engraved with the Mandala Jerusalema. The coasters are 112 mm (4 2/5") wide and 8 mm (1/3") thick.

This mold is part of the theme 'Jerusalema', which also includes the holder for these coasters, two trays and a set of 8 medallions, see some of the pictures (for illustrative purposes, this item is only for the coasters mold).

Silicone mold for four Slate coasters. The size of the coasters is approx. 11 x 13 cm (4 1/3" x 5 1/10") and they are 6 mm (1/4") thick. The edges of the coasters are coarsened, for that specific slate look and feel.

The coasters have a smooth surface, the 'crushed ice' effect that is visible in one of the pictures, is made with a set of inlay molds (separately available).

We also have a holder mold available that is specifically designed to hold 4 slate coasters, as shown in one of the pictures. Both molds are also available as a set, for a special setprice.

Silicone mold for a set of four Cascade Geode coasters. The coasters are about 12.5 cm (5") wide and 9 mm (1/3") thick. 

The coasters are made up of three layers of 3 mm each. Each layer has the same shape but is slightly smaller than the previous layer, which gives the sides of the coasters a unique cascade-like appearance.

There are also 2 Geode tray molds available with the same cascade design, see one of the pictures (for illustrative purposes, this items is only for the coasters mold). The large Cascade Geode tray is together with the Coaster mold also available as a set, at a special price.

Silicone mold for 4 Holographic Geode coasters. The coasters are 12.5 cm (5") wide and 8 mm (1/3") thick. These coasters are the same as our normal round Geode coasters, but then with a holographic color effect, which  will transfer to the surface of your resin coasters.

There are also matching holographic molds for a coaster holder and a large tray, see one of the pictures (for illustratives purposes, this item is only for the coaster mold). We also combined the 3 molds in 2 different available sets, for special setprices.

Silicone mold for a Royal Coaster XL. This supersized coaster is appr. 14.5 x 17 cm (5 2/3" x 6 2/3") and 1.5 cm ( 3/5") thick.

Because of this thickness, it's possible to create beautiful resin 3D-flowers and you can also use acrylic resins with this mold, like Jesmonite, Hydroflow and Artestone.

(The tealight candle holder, as seen in one of the pictures, is made with one of our other molds, and both molds are also as a set available).

Silicone mold for two round coasters with rough sides. The coasters have a diameter of 12.5 cm (5") and they are 12 mm (1/2") thick. The flat surface of each coaster is about 9 cm (3 1/2").

Introducing our mold for two Rough & Tough round coasters! The coasters that you create with this mold may look beaten up, but they are smooth and shiny on the top. They will also be solid as a rock, perfect for protecting your furniture from any spills. And don't worry, the mold can handle your toughest Resin and Acrylic Resin projects.

We also have other Rough & Tough molds available, for coasters and trays that all have the same beaten-up look and feel.

The Rough & Tough molds are also available in different sets of two molds, for special setprices.