Home Decor

Silicone mold for a medium sized matte Tree of Life symbol. This Tree of Life is 20 cm (8") wide and 15 mm (3/5") thick.

The iconic Tree of Life symbolizes growth, balance and harmony. Use your artistic talents to create a beautiful and unique symbol, embrace your inner tree hugger and add a touch of whimsy to every room.

!! ATTENTION: this mold doesn't have a glossy finish. Use it therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) Tree of Life, it will have a matte finish, as shown in some of the pictures.

We also have (a larger) Tree of Life mold available which has a glossy finish, perfect to use with epoxy resin.

Silicone mold for an Organic shaped Tealight Candle Holder. The candle holder is appr. 9 x 11 cm ( 3 1/2" x 4 1/3") and 4.5 cm (1 3/4") high.

The candle holder has a beautiful organic shape and it's very suitable for pouring flowers, for example.

You can also use acrylic resins with this mold, like Jesmonite, Hydroflow and Artestone.

We also have 'deep-pour' molds available for other tealight candle holders, as seen in some of the pictures (for illustrative purposes, this item is only for the Organic shaped tealight candle holder mold).

Silicone mold for a Square Tealight Candle Holder. The candle holder is 7.5 x 7.5 cm (3" x 3") and 4.6 cm (1 4/5") high. The cupsize is 58 mm (2 1/4")!

Because of the height and shape of the mold, it's very suitable for pouring flowers, for example.

You can also use acrylic resins with this mold, like Jesmonite, Hydroflow and Artestone.

We also have 'deep-pour' molds available for other tealight candle holders, as seen in some of the pictures (for illustrative purposes, this item is only for the Square tealight candle holder mold).

Silicone mold for a Round Tealight Candle Holder. The candle holder is 8 cm (3 1/6") wide and 6 cm (2 1/3") high.

The candle holder mold is pretty high and therefore very suitable for pouring flowers, for example.

You can also use acrylic resins with this mold, like Jesmonite, Hydroflow and Artestone.

We also have 'deep-pour' molds available for other tealight candle holders, as seen in some of the pictures (for illustrative purposes, this item is only for the Round tealight candle holder mold).

Silicone mold for an Easter Tealight Candle holder, featuring Little Thumper with his brothers and sisters! The candle holder is 16 cm (6 3/10") wide and 8 mm (1/3") thick.

You can find Little Thumper not only on this candle holder, he also appears on molds for a set of 4 coasters, a matching coaster holder, a large tray, a set of 8 medallions, a flower arranger and an egg holder tray. Everything you need to decorate a table for an Easter breakfast or Easter brunch!

Silicone mold for a clock with Funny Numbers, a wall clock with a diameter of 30 cm (12") and 6 mm (1/4") thick. The center hole for the movement is 8 mm (1/3") wide. The mold is mirrored, which means that you look at the backside of the clock.

The clock has two layers, the face of the clock is about 0.75 mm above the background. That's funny!

Silicone mold for a Holographic Tealight Candle Holder with decorative corners. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The decoration is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder with the Holographic Yin Yang symbol. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The symbol is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration, see the pictures. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder with a Holographic Fireplace. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The cosy and colorful fire is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration, see the pictures. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder, featuring a Holographic Color Burst. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Holographic Tealight Candle Holder with Rudolph the Red Nosed Reindeer. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. Rudolph is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Holographic Tealight Candle Holder with the AUM (OHM/OM) symbol. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep. The symbol is raised on the surface.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration, see the pictures. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder with a Druzy crystal Star. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder with Druzy crystal squares. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder with a Druzy crystal heart. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.

Silicone mold for a Tealight Candle Holder. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.

The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.

We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.

This particular candle holder is our basic model, without any decoration, so you can use all your creativity to make a beautiful candle holder.

We have 10 more models in our collection available, some with Druzy crystal shapes, some with Holographic features and some with Decorative corners, A few of them are pictured in their finished state.

Silicone mold for four different sets of clock numbers, one of which is for the Roman numerals 1 to 12. All numbers are 35 mm (1 2/5") tall and 5 mm (1/5") thick. The mold itself is 33,6 x 34 cm (13 1/4" x 13 2/5").

There are also 12 rhombuses, 12 dots, 12 bars with a straight end and 12 bars with a rounded end present, which gives you many options for a personalized clock.

The size of the numbers are perfect for our XL round disc mold and the XL round Geode tray mold, both 35.5 cm (14") wide, 10 mm (2/5") thick and separately available in the shop.