Holders and stands

This silicone mold can be used to make a holder for our Heart shaped coasters (which mold is available separately) and also a small Heart shaped tray. The heart is 18 cm (7") wide, 17 cm (6 3/4") tall and 8 mm (1/3") thick.

The two small hearts are meant to be used as stands on the tray, to create a holder for the heart shaped coasters and they can for instance be fixed with glue, resin or in a toplayer.

There are also molds available for a set of 4 heart shaped coasters and for a large heart shaped tray, see one of the pictures (for illustrative purposes, this item is only for the holder / small tray mold). 

We also combined the 3 molds in 2 different available sets, for special setprices.

This silicone mold can be used to make a holder for our Scallop coasters (which mold is available separately) and also a small Scallop tray. The scallop is 16.5 cm (6.5") x 14.5 cm (5 2/3") and 8 mm (1/3") thick.

The two small scallops are meant to be used as stands on the tray, to create a holder for the scallop coasters and they can for instance be fixed with glue, resin or in a toplayer.

There are Scallop molds available for a set of 4 coasters, trays in different sizes and for medallions, see one of the pictures (for illustrative purposes, this item is only for the holder / small tray mold).

Some of the scallop molds are also in two different sets available (coasters with holder, coasters with holder and large tray), for special setprices.

Silicone mold for a Holographic holder for 4 round Geode coasters, that are maximum 12.5 cm (5") wide and 8 mm (1/3") thick. The holder is the same as the holder for our normal round Geode coasters, but then with a holographic color effect, which  will transfer to the surface of your resin coaster holder.

This holder is specifically designed for our Holographic Geode Coasters, see one of the pictures (for illustratives purposes, this item is only for the holder mold). Both the holographic holder and matching coaster mold are as a set available, for a special setprice.

You insert the legs from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Silicone mold for a Holographic holder for 4 (holographic) Hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Hexagon coasters, see one of the pictures (for illustrative purposes, this item is only for the holder mold).

Both holographic molds are also as a set of 2 molds available, for a special setprice.

The six legs of the holder have to be attached from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Silicone mold for a holder for the Mandala Jerusalema coasters. 

The baseplate of the holder is engraved with the 'Mandala Jerusalema' and especially designed for the coaster set with the same engraving, see the pictures (for illustrative purposes, this item is only for the holder mold).

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The holder mold is part of our 'Mandala Jerusalema' design line, in which besides this mold are also a small and medium sized tray, a set of four coasters and a set of 8 medallions, as shown in some of the pictures (for illustrative purposes, this item is only for the holder mold).

The holder mold and coaster mold are also as a set available, for a special setprice.

Silicone mold for a holder for our Magical coasters.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is one of our molds with the Magical theme, which further consists of a coaster mold, 4 trays and a set of 8 medallions, see one of the pictures (for illustrative purposes, this item is only for the coaster holder mold).

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

The holder mold is also available in a Holographic version.

Silicone mold for a Holographic holder for 4 (holographic) Magical coasters. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Magical coasters, see one of the pictures (for illustrative purposes, this item is only for the holder mold). Both holographic molds are also as a set of 2 molds available, for a special setprice.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is also available in a normal version, without the holographic color effect.

Silicone mold for a holder for the Mandala Dahlia coasters.

The baseplate of the holder is engraved with the 'Mandala Dahlia' and especially designed for the coaster set with the same engraving, see the pictures (for illustrative purposes, this item is only for the holder mold).

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The holder mold is part of our 'Mandala Dahlia' design line, in which besides this mold are also a large tray, a set of four coasters and a set of 8 medallions, as shown in some of the pictures (for illustrative purposes, this item is only for the holder mold).

The holder mold and coaster mold are also as a set available, for a special setprice.

Silicone mold for a Holder for our 'Merry Christmas' coasters. The holder has the same decorative engraving as the 'Merry Christmas' coasters and tray.

The legs of the holder are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the 6 mm (1/4") thick base plate. You can fix the legs with a drop of glue or (UV) resin, so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The mold is also avalaible in a set with the coaster mold and in a set with both the coaster and tray mold, as shown in on of the pictures (for illustrative purposes, this item is only for the holder mold).

Silicone mold for a holder for our Oriental coasters.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is one of our molds with the Oriental theme, which further consists of a coaster mold, 4 trays and a set of 8 medallions, see one of the pictures for some of them (for illustrative purposes, this item is only for the coaster holder mold).

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Silicone mold for a holder for Oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, 8 mm (1/3") thick and it can hold 4 of our oval coasters.

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

There are also molds for matching coasters and for two oval trays available, see one of the pictures (for illustrative purposes, this item is only for the oval holder mold).

We have the molds also in two sets available (coasters with holder, coasters with holder and large tray), for special setprices.

There is also a mold available for the same size oval coaster holder, but then engraved with thin 'Graceful lines'.

Silicone mold for a holder for Oval coasters 'Graceful lines'. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and it can hold 4 of our oval coasters. The baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines.

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Silicone mold for a holder for four Geode coasters which are 15 mm (3/5") thick. The holder itself is 12 mm (1/2") thick and only suitable for our matching 15 mm thick irregular shaped Geode coasters, see some of the pictures (for illustrative purposes, this item is only for the holder mold).

You can also pour two feet with this mold, they can be attached to the holder with glue or (UV) epoxy.

Both molds are also as a set available and the holder has the same shape as our rectangular Geode trays which are also available in the shop.

Silicone mold for a holder for our Ocean themed coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. 

You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Silicone mold for a Holder for our Cute Christmas coasters. The holder is engraved with a bunch of cute Christmas figures and it's suitable for every round coaster with a diameter of 10 cm (4"), but it's especially meant for our Cute Christmas coasters.

The legs of the holder are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the 6 mm (1/4") thick base plate. You can fix the legs with a drop of glue or (UV) resin, so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The figures in the holder present themself also in a set of 4 coasters, a large 30 cm (12") Christmas tray and in 12 cute Christmas ornaments, for which we have molds available separately.

Silicone mold for a holder for our Lily Mandala coasters. 

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This holder mold is part of our Lily Mandala line, in which besides this mold are also molds available for a set of 4 coasters, a set of 8 medallions and a tray of 25 cm (10"), as shown in one of the pictures (for illustrative purposes, this item is only for the coaster mold).

The holder mold and coaster mold are also as a set available, for a special setprice.

Silicone mold for a holder for our Easter coasters, featuring Little Thumper with his brothers and sisters! The holder can hold 4 coasters of 10 cm (4") wide and 8 mm (1/3") thick.

You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This holder is a perfect match for the Easter coasters with the same engraved design, see one of the pictures (for illustrative purposes, this item is only for the holder mold).

Both molds are also as a set available, for a special setprice.

You can find Little Thumper not only on this mold and the coaster mold, he also appears on molds for a large tray, a set of 8 medallions, a tealight candle holder, a flower arranger and an egg holder tray. Everything you need to decorate a table for an Easter breakfast or Easter brunch!

 Silicone mold for a holder for our 'Mandala Peacock' coasters. 

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The holder mold is part of our 'Peacock Mandala' design line, in which besides this mold are also three cake stand molds (with center hole), a set of four coasters and a mold for 8 medallions.

The holder mold and coaster mold are also as a set available, for a special setprice.