Holders and stands

Silicone mold for a holder for our Fantasy coasters.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This mold is one of our molds with the Fantasy theme, which further consists of a coaster mold, 4 trays, 2 cakestands and a set of 8 medallions,.

Several of these molds are in sets available, for special setprices.

The holder mold is also in a holographic version available, for spectacular color effects on the surface of your resin coaster holder, especially when combined with the holographic Fantasy coasters.

Silicone mold for a holder for Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 8 mm (1/4") thick. 

You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Silicone mold for a holder for four coasters. It can hold four coasters which are maximum 6 mm (1/4") thick. The edge of the holder is coarsened and it is especially designed for our Slate coasters, for which we have a mold available too.

The holder mold and coaster mold are also as a set available, for a special setprice.

Silicone mold for a holder for 4 round Geode coasters, that are maximum 12.5 cm (5") wide and 8 mm (1/3") thick. The holder is specifically designed for our Round Geode Coasters.

This item is only for the coaster holder mold, but both the holder and matching coaster mold are as a set available, for a special setprice.

A set with this holder mold, the coaster mold and a mold for a large round Geode tray of 25 cm (10") is available as well, see one of the pictures (for illustratives purposes, this item is only for the holder mold).

You insert the legs from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

The Geode coaster holder mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a holder for four Hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. The six legs of the holder have to be attached from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

This holder mold is part of our line of Hexagon molds, in which besides this mold are also molds for matching coasters, two hexagon trays, a set of eight hexagon medallions and a set of eight hexagon napkin rings.

There are two special prized hexagon sets of 3 molds available with this holder mold, one set with the hexagon coasters and the medium sized hexagon tray and one set with the hexagon coasters and the large hexagon tray.

The holder mold is also in a holographic version available, for spectacular color effects on the surface of your resin coaster holder, especially when combined with the holographic Hexagon coasters.

Silicone mold for a holder for our coasters with a 'Tetris' pattern. The holder is large enough for four coasters of 10 x 10 cm (4" x  4") and 6 mm (1/4") thick. You can fix the supports with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Silicone mold for a coaster holder with ribbed edge. The holder can hold 4 coasters that are 10 cm (4") wide and 8 mm (1/3") thick and it is specifically designed for our round coasters with ribbed edges, but other round coasters of maximum 10 cm wide will fit too.

The legs of the holder are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Slicone mold for a Holographic telephone stand. We call this specific effect 'Crazy Holo' and the holographic color effect will transfer to the surface of your resin telephone stand.

The stand is 6 mm ( 1/4") thick and the space above the edge is 80 mm (3 3/5") wide and 130 mm (5 1/10") high.

The same design is also available in a regular version, without holographic effect.

Silicone mold for a large Tablet stand with a Holographic Broken Glass pattern. The holographic color effect will transfer to the surface of your tablet stand.

The stand is suitable for all tablets, small and large. It is 6 mm (1/4") thick and the frontplate above the edge is 22.5 cm (11") wide and 16.5 cm (6 2/5") high.

The same design is also available in a smooth version, without pattern.

Silicone mold for a Business Card holder with a Holographic Broken Glass pattern. The holographic color effect will transfer to the surface of your resin card holder. The holder is 5 mm (1/5") thick and 70 mm (2 3/4") wide, suitable for landscape Business Cards (European and American dimensions).

The same design is also available in a smooth version, without pattern.

Silicone mold for a holographic holder for 4 round coasters of 8 mm (1/3") thick. The holder is suitable for every round coaster with a diameter of 10 cm (4"), but it's especially meant for our holographic round coasters, for which we have a mold available separately.

The legs of the holder have a holographic finish too, they are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the 6 mm (1/4") thick base plate. You can fix the legs with a drop of glue or (UV) resin, so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Silicone mold for a telephone stand. The stand is 6 mm ( 1/4") thick and the space above the edge is 80 mm (3 3/5") wide and 130 mm (5 1/10") high.

The same mold is also available in a holographic version, see one of the pictures (for illustrative purposes, this item is only for the non-holographic mold).

There is also a mold available for an XL telephone stand, which is a good match for the larger (smart)phones. One of the pictures shows the size difference between the two stands.

Silicone mold for a Holographic holder for 4 (holographic) Fantasy coasters. The holder has a holographic color effect, which will transfer to the surface of your resin coaster holder.

The holder mold is also available in a normal version, without the holographic effect.

This holder is a perfect match for the Holographic Fantasy coasters, see one of the pictures (for illustrative purposes, this item is only for the holographic holder mold). Both holographic molds are also as a set of 2 molds available, for a special setprice.

The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.