544 products
544 products
Sort by:
Set of 2 molds - Slate coasters with holder
Set of 2 molds - Slate coasters with holder
Set of two silicone molds for four Slate coasters and a matching holder. The slates are approx. 11 x 13 cm (4 1/3" x 5 1/10") and they are 6 mm (1/4") thick. The edges of the coasters and holder are coarsened, for that specific slate look and feel.
There is also a matching oval slate tray available, see one of the pictures (for illustrative purposes, the tray mold is not included in this item).
The molds are also available separately.
Set of 2 molds - Tube Coaster Duo with Tray
Set of 2 molds - Tube Coaster Duo with Tray
Two silicone molds for:
- a set of two Tube coasters. The coasters are 12.5 x 12.5 cm (5" x 5") wide and 1 cm thick.
- a Tube tray. The tray is 12.5 x 25 cm (5" x 10") wide and 1 cm (2/5") thick.
Both the coasters and the tray have a flat bottom and the top consists of 5 adjacent tubes.
!! ATTENTION: these mold don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in shiny (glossy) coasters and tray, they will have a matte finish, as shown in the pictures.
The molds are also available separately.
Set of 2 molds - Tumbled Marble Coasters with Tray
Set of 2 molds - Tumbled Marble Coasters with Tray
Two silicone molds for:
- 4 square coasters with a rough tumbled marble look and feel. The coasters are 10 x 10 cm (4" x 4") wide and 1 cm (2/5") thick.
- a square tray with a rough tumbled marble look and feel. The tray is 20 x 20 cm (8" x 8") wide and 1 cm (2/5") thick.
!! ATTENTION: these molds don't have a glossy finish. Use them therefore with Jesmonite, Jesin, A1 and similar products that consist of water-based acrylic hardeners in combination with mineral powders. Pouring with resin will not result in a shiny (glossy) set of coasters and tray, they will have a matte finish.
The molds are also available separately.
Set of 2 molds - Whitch's Cauldron coasters and large tray
Set of 2 molds - Whitch's Cauldron coasters and large tray
Double, double toil and trouble, fire burn and cauldron bubble! (William Shakespeare)
Two silicone molds for:
- 4 coasters in the shape of a Whitch's Cauldron!! The coasters are 12.5 cm (5") wide, about 10 cm (4") high and 8 mm (1/3") thick.
- a large Whitch's Cauldron tray. The tray is 30 cm (12") wide, about 24 cm (9 1/3") high and 8 mm (1/3") thick.
The coasters and tray will be beautiful as Halloween decoration. The molds are also available separately.
Set of 2 molds - Yin Yang (sunflower) coasters with matching holder
Set of 2 molds - Yin Yang (sunflower) coasters with matching holder
- a set of four round coasters with a Yin Yang (sunflower) pattern engraved into them and with a diameter of 10 cm (4"). The coasters are 8 mm (1/3") thick.
- a matching holder. The legs of the holder are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
Set of 2 Ocean molds - coasters with matching holder
Set of 2 Ocean molds - coasters with matching holder
Two silicone molds for:
-
a set of four square coasters with an engraved Ocean theme. The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
- a holder for the Ocean coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x 4") and 8 mm (1/4") thick. You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
Set of 2 Tetris molds - Square coasters with raised edge + holder
Set of 2 Tetris molds - Square coasters with raised edge + holder
Two silicone molds for:
- a set of four square coasters with a raised edge and a 'Tetris' pattern. The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
-
a matching holder, which holds 4 coasters of maximum 8 mm (1/3") thick. You can fix the supports with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.
The coaster mold and the holder mold are also separately available.
Set of 2 trays - Mandala Jerusalema (S + M)
Set of 2 trays - Mandala Jerusalema (S + M)
Each tray is also separately available.
Set of 3 flower molds - Daisy
Set of 3 flower molds - Daisy
- The coasters are 12.5 cm wide (5") and 8 mm ( 1/3") thick.
- The tray is about 25 cm (10") wide and 8 mm (1/3") thick.
- The base plate of the holder is about 16.5 cm (6 1/2") wide and 8 mm ( 1/3") thick. There are four supports to keep the coasters in place, they can be attached to the base plate with glue or with a few drops of resin. And they can also be fixed in a final resin layer. The supports are 40 mm (1 3/5") tall and a paper template will be supplied to position them exactly.
Set of 3 flower molds - Geranium
Set of 3 flower molds - Geranium
- The coasters are 12.5 cm wide (5") and 8 mm ( 1/3") thick.
- The tray is about 25 cm (10") wide and 8 mm (1/3") thick.
- The base plate of the holder is about 16.5 cm (6 1/2") wide and 8 mm ( 1/3") thick. There are five supports to keep the coasters in place, they can be attached to the base plate with glue or with a few drops of resin. And they can also be fixed in a final resin layer. The supports are 40 mm (1 3/5") tall and a paper template will be supplied to position them exactly.
Set of 3 Hexagon molds - coasters with matching holder and large tray
Set of 3 Hexagon molds - coasters with matching holder and large tray
Three silicone molds for:
- a set of four Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick.
- a holder for the Hexagon coasters. The holder is large enough for hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. You can fix the six legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
- a large Hexagon tray. The tray is 31 cm (12 1/8") wide, measured from corner to opposite corner, and 8 mm (1/3") thick.
Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.
Set of 3 Hexagon molds - coasters with matching holder and medium tray
Set of 3 Hexagon molds - coasters with matching holder and medium tray
Three silicone molds for:
- a set of four Hexagon coasters. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick.
- a holder for the Hexagon coasters. The holder is large enough for hexagon coasters which are from side to side 10 cm (4") wide and 8 mm (1/3") thick. You can fix the six legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
- a medium sized Hexagon tray. The tray is 23 cm (9") wide, measured from corner to opposite corner, and 8 mm (1/3") thick.
Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.
Set of 3 Kintsugi molds - coasters with matching holder and tray
Set of 3 Kintsugi molds - coasters with matching holder and tray
Three silicone molds for:
- a set of four square Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The coasters are 10 x 10 cm (4" x 4") and 8 mm (1/3") thick.
- a holder for the Kintsugi coasters. The holder is large enough for four coasters of 10 x 10 cm (4" x 4") and 8 mm (1/4") thick. You can fix the legs with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
- a square Kintsugi tray. The tray is 25 x 25 cm (10" x 10") and 8 mm (1/3") thick.
Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.
The molds are also available separately.
Set of 3 molds - Holographic Magical coasters with holder and tray
Set of 3 molds - Holographic Magical coasters with holder and tray
- a set of four Magical coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.
- a matching holder. The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
- a large Magical tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.
These silicone molds have holographic color effects, which will transfer to the surface of your resin artwork. The molds are also available in a regular version, without the holographic color effect.
Set of 3 molds - 'Merry Christmas' Coasters with holder and tray
Set of 3 molds - 'Merry Christmas' Coasters with holder and tray
- a set of four round coasters with a decorative 'Merry Christmas' engraving. The coasters are 10 cm ( 4") wide and 8 mm (1/3") thick.
- a matching holder. You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
- a large 'Merry Christmas' tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.
Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.
Set of 3 molds - Cute Christmas Coasters with holder and tray
Set of 3 molds - Cute Christmas Coasters with holder and tray
- a set of four Cute Christmas coasters. The coasters are 10 cm ( 4") wide, 8 mm (1/3") thick and they are engraved with a bunch of cute Christmas figures.
- a matching holder. You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
- a large Cute Christmas tray. The tray is 30 cm (12") wide and 8 mm (1/3") thick.
Note: do not apply too thick a dome layer on the legs of the holder, because then they will no longer fit through the slots.
The figures in these molds present themself also in 12 cute Christmas ornaments, for which we have a mold available separately.
Set of 3 molds - Decorative Christmas ornaments
Set of 3 molds - Decorative Christmas ornaments
Three silicone molds for Decorative Christmas ornaments, one with a Christmas tree, one with a Snowflake and one with a Curls design. Each ornament is 15 cm (6") tall, 11 cm (4 1/3") wide and 6 mm (1/4") thick. The decorative pattern on the ornaments are 0.75 mm thick and they will be raised on the surface of the ornaments.
The molds are also available separately.
Set of 3 molds - Druzy Crystal Christmas ornaments
Set of 3 molds - Druzy Crystal Christmas ornaments
Three silicone molds for Druzy Crystal Christmas ornaments, one with a Christmas tree, one with a Christmas star and one with a Cristmas bell. Each ornament is 15 cm (6") tall, 11 cm (4 1/3") wide and 6 mm (1/4") thick.
The molds are also available separately.
Set of 3 molds - Fantasy coasters with holder and tray
Set of 3 molds - Fantasy coasters with holder and tray
- a set of four 'Fantasy' coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.
- a matching holder. The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
- a large 'Fantasy' tray. The tray is 25 cm (10") wide and 8 mm (1/3") thick.
Set of 3 molds - Fantasy trays (S + M + L)
Set of 3 molds - Fantasy trays (S + M + L)
Set of three silicone molds for our trays with the Fantasy theme. The trays are 15 cm (6"), 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.
These three molds are part of our molds with the Fantasy theme, which further consists of a coaster mold, a coaster holder, 1 larger tray, 2 cakestands and a set of 8 medallions.
We made several of these molds in sets available, for special setprices.
Set of 3 molds - Heart shaped coasters with holder and large tray
Set of 3 molds - Heart shaped coasters with holder and large tray
Three silicone molds for:
- a set of 4 Heart shaped coasters. The coasters are 14.5 cm (5 7/10") wide. 13.5 cm (5 1/3") tall and 8 mm (1/3") thick.
- a mold that can be used to make a holder for the coasters and also a small Heart shaped tray. The heart is 18 cm (7") wide, 17 cm (6 3/4") tall and 8 mm (1/3") thick.
The two small hearts are meant to be used as stands on the tray, to create a holder for the heart shaped coasters and they can for instance be fixed with glue, resin or in a toplayer. - a large Heart shaped tray. The tray is 30 cm (12") wide, 27.8 cm (11") tall and 8 mm (1/3") thick.
All molds are also available separately.
Set of 3 molds - Holographic Fantasy coasters with holder and tray
Set of 3 molds - Holographic Fantasy coasters with holder and tray
- a set of four Fantasy coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.
- a matching holder. The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
- a large Fantasy tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.
These silicone molds have holographic color effects, which will transfer to the surface of your resin artwork. The molds are also in a normal version available, without holographic effect.
Set of 3 molds - Holographic round Geode tray with coasters and holder
Set of 3 molds - Holographic round Geode tray with coasters and holder
- a large round geode tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick.
- a set of four round Geode coasters. The coasters are 12.5 cm (5") wide and 8 mm (1/3") thick.
- a matching holder. This holder is suitable for the 4 Geode coasters. You insert the legs from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
These silicone molds have holographic color effects, which will transfer to the surface of your resin artwork. The molds are also in a normal version available, without holographic effect.
Set of 3 molds - Magical coasters with holder and tray
Set of 3 molds - Magical coasters with holder and tray
- a set of four 'Magical' coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.
- a matching holder. The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
- a large 'Magical' tray. The tray is 25.5 cm (10") wide and 8 mm (1/3") thick.
Showing 456/544