Products

Set of two silicone molds for 4 Holographic Hexagon coasters and a matching holder. The coasters are from side to side 10 cm (4") wide and 8 mm (1/3") thick. The matching holder can hold four Hexagon coasters of 8 mm thick. 

The silicone molds have holographic color effects, which  will transfer to the surface of your resin artwork. Both molds are also in a normal version available, without holographic effect.

The six legs of the holder have to be attached from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Two silicone molds for a large and an extra large Trinket Dish. The large Trinket Dish is 15 x 30 cm (6" x 12") wide and the extra large Trinket Dish is 17.5 x 35 cm (7" x 14") wide.

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire side 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Two silicone molds for a large and an XL round Trinket Dish. The large Trinket Dish has a diameter of 23 cm (9") and the XL Trinket Dish has a diameter of 28 cm (11").

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire disc 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Besides these two molds there are also Lily molds available for a set of 8 medallions and a tray of 25 cm (10"), as shown in one of the pictures (for illustrative purposes, this item is only for the coaster and holder mold).

Set of two silicone molds for our trays with the Magical theme. The trays are 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These two molds are part of our molds with the Magical theme, which further consists of a coaster mold, a coaster holder mold, a smaller tray, a larger tray and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Set of two silicone molds for our trays with the Magical theme. The trays are 15 cm (6") and 20 cm (8") wide and 8 mm (1/3") thick.

These two molds are part of our molds with the Magical theme, which further consists of a coaster mold, a coaster holder, 2 larger trays and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Two silicone molds for a medium size and a large round Trinket Dish. The medium Trinket Dish has a diameter of 18 cm (7") and the large Trinket Dish has a diameter of 23 cm (9").

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire disc 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Two silicone molds for a medium size and a large Trinket Dish. The medium Trinket Dish is 12.5 x 25 cm (5" x 10") wide and the large Trinket Dish is 15 x 30 cm (6" x 12") wide.

Both Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.

The raised edge of each dish is along the entire side 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!

The molds are also available separately.

Set of two silicone molds for our trays with the Oriental theme. The trays are 20 cm (8") and 25 cm (10") wide and 8 mm (1/3") thick.

These two molds are part of our molds with the Oriental theme, which further consists of a coaster mold, a coaster holder mold, a smaller tray, a larger tray and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Set of two silicone molds for our trays with the Oriental theme. The trays are 15 cm (6") and 20 cm (8") wide and 8 mm (1/3") thick.

These two molds are part of our molds with the Oriental theme, which further consists of a coaster mold, a coaster holder, 2 larger trays and a set of 8 medallions.

Some of these molds are also in a set of 2 or 3 molds available, for special setprices.

Two silicone molds for:

• 4 Oval coasters. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide and 8 mm (1/3") thick. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

Two silicone molds for:

• 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
• a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the supports, because then they will no longer fit through the slots.

There are also molds available for two oval trays with the same graceful line pattern.

These two molds are together with the large oval tray 'Graceful lines' also as a set of 3 molds available, for a special setprice.

Two silicone molds for:

• 4 coasters in the shape of a Pumpkin. The coasters are 12.5 cm (5") wide, 12 cm (4 3/4") tall and 8 mm (1/3") thick.
• a large Pumpkin tray. The tray is 28 cm (11") wide, 27 cm (10 2/3") tall and 8 mm (1/3") thick.

Make your Halloween spooktacular with these 2 molds, perfect for adding a touch of autumnal fun to your seasonal decorations. Trick or treat!

The molds are also available separately.

Two silicone molds for:

• a set of two Geode Coasters with rough sides. The coasters are about 14 x 11.5 cm (5 1/2" x 4 1/2") wide and 12 mm (1/2") thick. 
• a Geode tray with rough sides. The tray is about 22 x 26 cm (8 2/3" x 10 1/4") wide and 12 mm (1/2") thick.

This beautiful set of 2 molds will inspire you to explore your creativity and design your very own unique Geode set. The molds are though, thick and sturdy, the tray and coasters have rough sides and a distinct design, like Geode slices, perfect for creating unique works of art. Bring your imagination to life with this exclusive set.

We also have other Rough & Tough molds available, for coasters and trays that all have the same beaten-up look and feel.

Two silicone molds for:

• a set of two round coasters with rough sides. The coasters have a diameter of 12.5 cm (5") and they are 12 mm (1/2") thick. The flat surface of each coaster is about 9 cm (3 1/2"). 
• a round tray with rough sides. The tray has a diameter of 22.5 cm (9") and it is 12 mm (1/2") thick.

These two molds are thick and rough, and still have a shiny surface! Perfect to create a rock-solid set of coasters and tray that will be a beautiful decoration on any table. With your creativity and inspiration, the possibilities with Resin and Acrylic Resin are endless. Don't be afraid to get rough and tough with these molds, let your imagination run wild!

We also have other Rough & Tough molds available, for coasters and trays that all have the same beaten-up look and feel.

Two silicone molds for:

• a set of two square Geode-style coasters with rough sides. The coasters are about 12.5 x 12.5 cm (5" x 5") wide and 12 mm (1/2") thick. The flat surface of each coaster is about 9 x 9 cm (3 1/2" x 3 1/2"). 
• a large Rectangular Geode-style tray with rough sides. The tray is about 18 x 31 cm (7" x 12") wide and 12 mm (1/2") thick.

This beautiful set of 2 molds will inspire you to explore your creativity and design your very own unique set. The molds are though, thick and sturdy, the tray and coasters have rough sides and a distinct natural stone-like design, perfect for creating unique works of art. Bring your imagination to life with this exclusive set.

We also have other Rough & Tough molds available, for coasters and trays that all have the same beaten-up look and feel.

Set of 2 silicone molds for 4 Round Geode coasters and a matching holder. The coasters have the same shape as our round Geode trays, but then smaller, they are about 12.5 cm (appr. 5") wide and 8 mm (appr. 1/3") thick. The holder is specifically designed for these coasters.

The molds are also available seperately.

A set with these two molds and a mold for a large round Geode tray of 25 cm (10") is available as well, see one of the pictures (for illustratives purposes, this item is only for the coaster and holder mold).

You insert the legs of the holder from the bottomside through the slots of the base plate and you can fix them with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

Both molds are also in a holographic version available, for spectacular color effects on the surface of your resin coasters and holder!

Set of 2 molds:

• a Royal Coaster XL. This supersized coaster is appr. 14.5 x 17 cm (5 2/3" x 6 2/3") and 1.5 cm ( 3/5") thick.
• a round Tealight Candle Holder. The candle holder is 8 cm (3 1/6") wide and 6 cm (2 1/3") high.

Because of the thickness of the Royal coaster, it's possible to create beautiful resin 3D-flowers in it. The candle holder mold is pretty high and therefore very suitable for pouring flowers, for example.

You can also use acrylic resins with this mold, like Jesmonite, Hydroflow and Artestone.

 Both molds are also separately available.

Two silicone molds for:

• a set of 4 Scallop coasters. The coasters are 12.5 cm (5") x 11 cm (4 1/3") and 8 mm (1/3") thick.
• a mold that can be used to make a holder for the Scallop coasters and also a small Scallop tray. The scallop is 16.5 cm (6.5") x 14.5 cm (5 2/3") and 8 mm (1/3") thick .
  The two small scallops are meant to be used as stands on the tray, to create a holder for the scallop coasters and they can for instance be fixed with glue, resin or in a toplayer.

There are also Scallop molds available for 2 larger trays and for medallions, see one of the pictures (for illustrative purposes, this item is only for the coaster mold with holder / small tray mold).