Sort by:
620 products
620 products
Silicone mold for a Tealight Candle Holder with Druzy crystal squares. The backpanel is 10 x 10 cm (4" x 4") and the holder is 6 mm (1/4") thick. The maximum cupsize is 41 mm (1 3/5"), the recess for the cup is about 3 mm (1/10") deep.
The candle holder is made of two parts, fixed together with a finger joint connection and a few drops of glue, or epoxy, are sufficient for a permanent connection.
We tested the candle holder with a standard burning tealight, without any issues of overheating. It's always a good idea though, to place 4 small rubber feet under the holder, so that air can flow under the tealight.
We have 10 more models in our collection, some with Druzy crystal shapes, some with Holographic features (with or without decorative corners) and one basic model, without any decoration. A few of them are pictured in their finished state.
Silicone mold for a Business Card holder with a Holographic Broken Glass pattern. The holographic color effect will transfer to the surface of your resin card holder. The holder is 5 mm (1/5") thick and 70 mm (2 3/4") wide, suitable for landscape Business Cards (European and American dimensions).
The same design is also available in a smooth version, without pattern.
Two silicone molds for:
- 28 Domino stones. These are special stones because the dots are hexagon shaped and the surface of the stones is uneven, which gives each stone a unique look! The stones are 24 mm x 50 mm (appr. 1" x 2") and about 6 mm (1/4") thick.
- a tray to store the 28 Domino stones, to better prevent them from getting lost. The dimensions of the tray are 21 cm x 25 cm (8 1/3" x 10") and it is in total 1 cm (2/5") thick. The tray has two layers, one for the decorative border, which is 6 mm (1/4") thick and a second layer of 4 mm (1/6") for the baseplate. The baseplate has a decorative pattern engraved into it.
This medallion mold can be used together with our mold for the (napkin) rings, which is especially designed to form the base for these medallions. Together they make a unique napkin ring.
(The mold for the rings is separately available, the photo that shows both the medallion mold and ring mold is for illustrative purposes only. In this article only the medallion mold is included.)
Silicone mold for a set of four Cascade Round coasters. The coasters are 11 cm (4 1/3") wide and 9 mm (1/3") thick.
The coasters are made up of three layers of 3 mm each. Each layer is slightly smaller than the previous layer, which gives the sides of the coasters a unique cascade-like appearance.
There is also a large round tray mold available with the same cascade design, see one of the pictures (for illustrative purposes, this items is only for the coasters mold). Both molds are also available as a set, at a special price.
Silicone mold for a decorative Halloween shield with a Mystical Witch! The shield is 17 cm (6 2/3") wide, 25 cm (10") high and 8 mm (1/3") thick. The decorative design is 0.75 mm thick and it will be raised on the surface of the shield.
Use this mold to create and decorate your interior or frontdoor with a Halloween shield, featuring a Mystical Witch, a scary cat and some huge bats! Perfect for adding a bit of spooky fun to your Halloween decor. Get ready to scare (in a cute way) with a unique homemade decoration shield.
We also have 3 other molds available for a Halloween shield, all with their own decorative design.
Silicone mold for a large heart that is perforated with 66 holes, evenly spaced along the edge of the heart. The heart is 25 cm (10") wide, 23 cm (9") high and 8 mm (1/3") thick.
Make your Love craft projects extra special with this perforated heart. It features 66 holes around the edge, perfect for all your fabric, ribbon, wicker and crochet projects. Unleash your imagination, see what surprises you discover and bring the love into your home decor with this perforated heart!
- a set of four 'Magical' coasters. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.
- a matching holder. The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
Some of these molds are also in a set of 2 or 3 molds available, for special setprices.
Four silicone inlay molds for Round coasters. The molds are 9 cm (3 1/2") wide and they are a perfect match for our mold for 10 cm (4") round coasters. And because the inlay molds are appr. 4 mm (1/6") thick, your result will be a coaster with a raised edge and a beautiful engraved surface.
We also have a few other round inlay molds available with a different pattern, see one of the pictures.
Three of these molds are also as a set available, for a special setprice.
The mold comes with a few extra's, namely included molds for a small heart and a cute teddy bear.
Three of these molds are also as a set available, for a special setprice.
Set of 3 molds - medium, large and XL round Trinket Dish
Set of 3 molds - medium, large and XL round Trinket Dish
Three silicone molds for a medium size, a large and an XL round Trinket Dish. The medium Trinket Dish has a diameter of 18 cm (7"), the large Trinket Dish 23 cm (9") and the XL Trinket Dish 28 cm (11").
The Trinket Dishes have two layers, the baselayer is 8 mm (1/3") thick and the raised edge is 6 mm (1/4") high. The dishes are in total 14 mm (just over 1/2") thick.
The raised edge of each dish is along the entire disc 5 mm (1/5") narrower than the baselayer, giving the Trinket Dish an elegant appearance!
The molds are also available separately.
Silicone mold for a large 'Oriental' tray. The tray is 25.5 cm (10") wide and 8 mm (1/3") thick.
This mold is one of our molds with the Oriental theme, which further consists of a coaster mold, a coaster holder mold, 2 smaller trays, a larger tray and a set of 8 medallions, see one of the pictures for some of them (for illustrative purposes, this item is only for the large tray mold).
Some of these molds are also in a set of 2 or 3 molds available, for special setprices.
Set of 3 molds - Oval coasters with holder and large tray 'Graceful lines'
Set of 3 molds - Oval coasters with holder and large tray 'Graceful lines'
Three silicone molds for:
- 4 Oval coasters, engraved with thin graceful lines. The coasters are 9.5 x 12.5 cm (3 3/4" x 5") wide and 8 mm (1/3") thick.
- a holder for these oval coasters. The holder is 12.5 x 16.5 cm (5" x 6 1/2") wide, the baseplate is 8 mm (1/3") thick and it is engraved with thin graceful lines. You can fix the supports of the holder with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
- a large Oval tray. The tray is 17 x 25 cm (6 2/3" x 9 5/6") wide, 1 cm (2/5") thick and it is engraved with thin graceful lines.
Note: do not apply too thick a dome layer on the supports of the holder, because then they will no longer fit through the slots.
Silicone mold for a small Holographic Geode tray. The tray is 18 cm (7") wide and 8 mm (1/3") thick.
The mold has a holographic color effect, which will transfer to the surface of your resin artwork.
We have the same holographic tray also in a larger 28 cm (11") version available.
Silicone mold for a large Scallop tray. The tray is 25 cm (10") x 22.5 cm (9") and 8 mm (1/3") thick.
There are also Scallop molds available for a set of 4 coasters, a matching coaster holder / small tray, an XL tray and for medallions, see one of the pictures (for illustrative purposes, this item is only for the large tray mold).
Some of the scallop molds are also in two different sets available (coasters with holder, coasters with holder and this large tray), for special setprices.
Silicone mold for a coaster holder with ribbed edge. The holder can hold 4 coasters that are 10 cm (4") wide and 8 mm (1/3") thick and it is specifically designed for our round coasters with ribbed edges, but other round coasters of maximum 10 cm wide will fit too.
The legs of the holder are 40 mm (1 3/5") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
Besides the mold for the matching ribbed edge coasters, there are also ribbed edge molds available for trays in 3 different sizes, see one of the pictures (for illustrative purposes, this item is only for the coaster holder mold). Some of these molds are also in a set available, for a special setprice.
Four silicone inlay molds for Round coasters. The molds are 9 cm (3 1/2") wide and they are a perfect match for our mold for 10 cm (4") round coasters. And because the inlay molds are appr. 4 mm (1/6") thick, your result will be a coaster with a raised edge and a beautiful engraved surface.
We also have a few other round inlay molds available with a different pattern, see one of the pictures.
Four silicone inlay molds for Round coasters. The molds are 9 cm (3 1/2") wide and they are a perfect match for our mold for 10 cm (4") round coasters. And because the inlay molds are appr. 4 mm (1/6") thick, your result will be a coaster with a raised edge and a beautiful engraved surface.
We also have a few other round inlay molds available with a different pattern, see one of the pictures.
And this 'Mikado' pattern is also available for square and hexagon coasters, see one of the pictures (for illustrative purposes, this item is only for the square inlay molds).
Set of 2 molds - Peacock (Mandala) coasters with matching holder
Set of 2 molds - Peacock (Mandala) coasters with matching holder
- a set of four coasters, engraved with the Peacock Mandala. The coasters are 11.5 cm (4 1/2") wide and 8 mm (1/3") thick.
- a matching holder. The legs of the holder are 42 mm (1 2/3") tall and you insert them from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).
These two molds are part of our 'Peacock Mandala' design line, in which besides these molds are also three cake stand molds (with center hole) and a mold for 8 medallions.
Silicone mold for a holder for our coasters with a 'Tetris' pattern. The holder is large enough for four coasters of 10 x 10 cm (4" x 4") and 6 mm (1/4") thick. You can fix the supports with a drop of glue or resin so that it becomes a solid piece (Tip: place the holder upside down, so that the supports will hang vertically while the glue or resin is drying).
This coaster holder is part of several molds with the 'Tetris' pattern, see the pictures (for illustration purposes, this item is only for the holder mold).
Three of these molds are also as a set available, for a special setprice.
Showing 360/620